Оценок - 4, средний балл: 4.3 ( )

Производитель: Braun Размер: 1.49 mb Название файла: Язык инструкции:

Failure to lock platform may result in unintended platform deployment. Unintended platform deployment may result in serious bodily injury and/or property damage. Note: The lift platform must be pushed back into its carriage compartment at least half-way before reverting back to normal (powered) operation. When the lift is fully extended manually, it does not activate the proper switches for normal operation. Returning (moving) the lift at least half-way in allows for proper switch activation. Note: Before manually raising or lowering platform, be sure to reengage the release cable mechanism by loosening (turning) the “T” handle and pushing inward. Failure to place “T” handle in the original IN position will allow the platform to move in and out when trying to raise or lower the platform with the hand pump. Sales Representative: Instruct and demonstrate the proper re- engagement procedure of the manual release for all new UVL owners at the point of sale or delivery. Remind the consumer of proper engagement procedures when giving telephone instructions. Step-by-step instructions for manually moving the platform in and out, manually raising and lowering the platform and manually lowering (unfolding) the outboard roll stop are provided on the following pages. Platform Carriage Assembly Drive Chain Reengagement Procedure: After manually moving the platform in or out: 1. Turn (loosen) the manual release “T” handle. 2. Push the “T” handle in fully (until handle bottoms out against its mounting bracket). Read warning posted above! 3. Grasp the outer roll stop and move the platform in and out until the platform locks (chain release assembly engages), securing the platform carriage assembly within the housing. You will feel the release mechanism engage. WARNING 81823 Push T-handle in fully andmanually move platform inand out to engage platformlock before driving vehicle.Failure to lock platform mayresult in unintended platformdeployment. Unintendedplatform deployment mayresult in serious bodily injuryand/or property damage. Do not remove! TOLOCK TURN2 1 To Manually Move Platform Out (Extend) From Stow Position: 2 1. Pull the “T” handle release Read warning posted above! cable outward. Before raising or lowering the 2. Turn the “T” handle to lock platform, be sure to lock the platform. Reengage the release platform into the released cable mechanism by loosening position. (turning) the “T” handle and 3. Carefully pull the platform out pushing inward. Failure to place “T” handle in the original IN to desired position. position (lock platform) will cause the platform to move in and out when trying to raise or lower the platform with the hand pump. WARNING 81823 Push T-handle in fully andmanually move platform inand out to engage platformlock before driving vehicle.Failure to lock platform mayresult in unintended platformdeployment. Unintendedplatform deployment mayresult in serious bodily injuryand/or property damage. Do not remove! TOLOCK TURN1 Page 16 Manual Operating Instructions Hand Pump Handle To Manually Raise Platform To Floor Level: A Hand Pump Release Valve maximum 30 inch lbs minimum 15 inch lbs seats (stops) OPENCLOSE approximate 1/16" intervals Valve Tightening Specification: Once valve seats (stops), tighten 15 to 30 inch pounds as shown. WARNING 81823 Push T-handle in fully andmanually move platform inand out to engage platformlock before driving vehicle.Failure to lock platform mayresult in unintended platformdeployment. Unintendedplatform deployment mayresult in serious bodily injuryand/or property damage. Do not remove! TOLOCK TURN Figure 1 b a Release Valve Note: Disregard procedures for manually moving the platform in or out if not applicable. 1. Remove pump handle from clips on side of power pack (or other storage location). 2. Place handle through pump cover access slot and into hand pump. Stroke hand pump until platform reaches floor height (see Photo C). 3. a. Pull “T” handle release cable outward and b. turn “T” handle to lock platform into the released position (see Figure 1). 4. Push platform in until it meets floor of vehicle (if applicable). 5. Reengage the release cable mechanism by a. turning the “T” handle and b. pushing the “T” handle in fully (see Figure 2). Note: Grasp the outer roll stop and move the platform in and out until the platform locks. You will feel the release mechanism engage. Read Platform Carriage Assembly Drive Chain Reengagement Procedure section on opposite page! Open (Down) Close (Up/Stop) B Hand Pump Handle C Figure 2 WARNING 182 Push T-handle in fully andmanually move platform inand out to engage platformlock before driving vehicle.Failure to lock platform mayresult in unintended platformdeployment. Unintendedplatform deployment mayresult in serious bodily injuryand/or property damage. Do not remove! TOLOCK TURN a b Page 17 Manual Operating Instructions Hand Pump Handle To Manually Lower Platform To Ground Level: WARNING 81823 Push T-handle in fully andmanually move...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: