Replace grills by aligning top ends of rods to upper set of holes on corresponding frames. Swing grilles towards frame in the same manner as they were removed and allow rod bottoms to fall into bottom holes until fully secured. Make sure all rods are completely inside holes. NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. FireCraft Technologies reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and pr

Remove fireplace grille assemblies by lifting up and out of holes on frame. Then pull from bottom out towards you. (Figures 1 and 2). Note: Lift grille near outer support rods to fully clear holes. Step 2. Insert grille trim onto grille and bend tabs over and around until fully secured (See Figure 3 ). Bend tabs utilizing the flat end of a screw driver or pliers. Step 3. Remove protective covering from decorative grille trim pieces and wipe with damp cloth. Step 4. Replace grills by aligning

Remove fireplace grille assemblies by lifting up and out of holes on frame. Then pull from bottom out towards you. (Figures 1 and 2). Note: Lift grille near outer support rods to fully clear holes. Step 2. Insert grille trim onto grille and bend tabs over and around until fully secured (See Figure 3 ). Bend tabs utilizing the flat end of a screw driver or pliers. Step 3. Remove protective covering from decorative grille trim pieces and wipe with damp cloth. Step 4. Replace grills by aligning

© 2000 by FCT P/N 750,054M REV. B 05/2001

Slightly lift and pull the existing top louver assembly away from the fireplace. Step 3. Slightly lift up the bottom hinged panel to disengage the small hooks on ether side of the panel. Pull forward and lower the panel down to open. Remove the assembly from the fireplace by removing the hinge screw on each end of the assembly. Step 4. Working with one assembly at a time, remove the existing black louvers separating the brackets from the assemblies (see Figure 1). To ease the removal of the br

Consult your local distributor for fireplace code information. Printed in U.S.A. © 2004 by LHP P/N 750,166M REV. B 07/2006 LHP 1110 West Taft Avenue Orange, CA 92865

The blower supplies air delivery at 105 CFM at 0" H2O static pressure, 90 CFM at 0.2" H2O static pressure. The maximum operating static pressure is 0.38" H2O. The FAB-1100 has been tested and certified by CSA. Always check local building codes. The installation must comply with local regulations as well as the National Electric Code. Failure to follow these instructions could cause a fireplace malfunction resulting in possible injury and/or property damage. PLEASE RETAIN THESE INSTRUCTIONS FOR F

Step 1. Remove screen and rod assemblies as shown in Figure 1. Step 2. Align the canopy with the holes in the side frames. Step 3. Install three screws as shown in Figure 2. Step 4. Make sure canopy is level and secure. Step 5. Reinstall screen and rod assemblies (see Figure 1) NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. LHP reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and the discontinuance of colors, styles and products.

1 ea. Surround Kit 1 ea. Surround Trim Kit 1 ea. Face Kit 1 ea. Instruction Sheet GENERAL INfORMATION All of these parts may scratch and bend, great care should be used in handling them. If you encounter any problems, need clarification of these instructions or are not qualified to properly install this kit, contact you local distributor or dealer. Read this instruction sheet in its entirety before beginning the installa face / Surround Panel Kits (Required) -Includes Black face, Surround, and B

56 ... 97 ... 103 104 ... 106 ... 1 1 1 1 0 0 0 0 1 0 1 2 1 2 0 1 2 2 0 2 0 0 2 0 58 ... 61 ... 64 ... 67 109 ... 116 121 ... 124 ... 1 1 1 1 0 1 1 1 0 1 0 2 1 0 1 0 0 3 3 3 2 0 0 0 68 ... 70 73 74 ... 128 130 135 ... 138 ... 1 1 1 1 1 1 1 1 0 1 0 0 0 1 2 0 1 3 3 0 2 0 0 3 79 80 82 82 ... 145 ... 147 ... 150 ... 152 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 4 0 4 0 0 3 0 3 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 13 Stabilizer A1 20' Max. B1 10' Max. Offset Elbow Figure 37 A1 C1 B1 B2 C2 A2 A1 C1 B1 B