Included in the box are 4 wheels, a handle and screws to install the wheels and handle. You will need a 1/4” nut driver and a Phillips screw driver. The unit has a low/off/high switch located on the backside of the unit. As each home has differences of size, occupancy, location, infiltration rates and homeowner needs, it is hard to estimate when the collectors will need to be changed. Because of the way air moves through the TFPC, the collectors are divided into 3 separate sections. Collectors

If they do not operate continuously, then interlocking them electrically with the TFP is acceptable. Consult a certified electrician. ATTENTION The TFP can be installed in several different ways. Please read all suggested methods before attempting installation. Electrical The TFP is equipped with a standard power supply, on a 5’ 5” cable. Lighted ON/OFF switch. C US * LEAVE FOR HOMEOWNER NOTE: Due to ongoing research and product development, specifications, ratings and dimensions are subject to

(Fig. 3) MOUNTING 1. Locate mounting bolts (4) on side of TFP cabinet for vertical hanging (Fig. 3) and remove. 2. Measure distance between the bolts and mark it on the floor/header joist where the TFP is to be hung. 3. Fasten hanging straps to floor joists using wide head nails or screws with washers. 4. Insert hanging bolts through prepunched holes in straps and lift TFP into position. Tighten and secure bolts. DUCTING 1. Install (2) 7” port collars (provided) on TFP cabinet with (8) 8/32” X 3

The two cores are arranged for highly efficient counter current airflow. MOTORS AND BLOWERS Each air stream has one centrifugal blower driven by a common ECM motor. 5 speed fan operation. 120 VAC, 1.4 Amps. FILTERS Washable air filters in exhaust and supply air streams. MOUNTING THE HRV Four threaded inserts at corners of case designed to accept four reinforced polyester straps that are supplied with the unit. DEFROST Damper defrost system. DEHUMIDISTAT Adjustable Internal Dehumidistat

If they do not operate continuously, then interlocking them electrically with the TFP is acceptable. Consult a certified electrician. WHOLEHOUSE AND PORTABLECONSOLE MODELS ATTENTION The TFP can be installed in several different ways. Please read all suggested methods before attempting installation. Electrical The TFP is equipped with a standard power supply, on a 5’ 5” cable. Lighted ON/OFF switch. * LEAVE FOR HOMEOWNER NOTE: Due to ongoing research and product development, specifications, ratin

4. A short piece (1-2 foot) of flexible ducting should be used on both sides of the TFP (Fig. 3). This will reduce vibration and noise transfer if present. NOTE: Please refer to the HRV installation manual for proper ducting of that appliance. Type 2 Installation *“Breathing T” is designed to assist in neutralizing pressure differences which can occur between HRV and TFP when joined together. TFP Hanging straps (4) Relief opening (breathing T) 6" port collars Power cord Flexible ducting Air flow

It is designed for line voltage wall mounting and is provided with a Single Pole - Single Throw snap action dustproof electrical switch. SPECIFICATIONS: MODEL: 99-129- Line Voltage Dehumidistat with screw terminals. •ELECTRICAL RATING: Line voltage only. (Up to 120 VOLT AC only). SCALE RANGE: 20 to 80% relative humidity with OFF and ON positions. SENSING ELEMENT: A thin (1 mm) moisture sensitive nylon ribbon. SETPOINT ADJUSTMENT: Control knob on face of Dehumidistat. OPERATING DIFFER

Drain connections 2 -1/2" (12 mm) OD. CONTROLS -ControlAir 15 -Standby/ON mode, 20 ON/ 40 OFF mode, Recirculation mode (on compatible units), (each mode has 5 speeds). Control pad can be removed from HRV and remotely mounted. WEIGHT 106 lbs. (48 kg) SHIPPING WEIGHT 108 lbs. (49 kg) PERFORMANCE Net supply airflow in cfm (L/s) against external static pressure 195TRV 300TRV E.S.P @ 0.1” (25 Pa) @ 0.2” (50 Pa) @ 0.3” (75 Pa) @ 0.4” (100 Pa) @ 0.5” (125 Pa) cfm L/s 203 (96) 191 (90) 182 (86) 167 (79)

The TRV is specifically designed for moderate/ temperate geographies with winter temperatures below freezing and summer conditions that are hot and humid. (Typically >75°F and 65% R.H.) The TRV is a new concept in ventilation that provides the compounded benefits of moisture transfer with unmatched heat recovery in a single unit. This new configuration is the only way to ensure year round temperature and moisture transfer. TRV TOTAL RECOVERY VENTILATOR • ASHRAE 62.2 Ventilation Standards • Sensi

Shim frame under any low sides. 4. After frame has been squared, straightened and shimmed, weld or attach frame securely to roof. MAX. SLOPE TOLERANCE: 1/16" per linear foot in any direction. Note specification of duct location on bottom of HRV when positioning cross members (duct cavity). Roof Curb Assembly Figure 1 side piece slot for tab wood nailer strip side piece slot for tab locking tab spike wood nailer strips tabs through slots end piece wood nailer strip end piece locking tab Figure 2