Mount C-TCB-21 into vehicle: • Position pole support assembly between seat base mount and floor of vehicle • Align holes in pole support assembly with holes in seat base. • Loosely attached factory seat bolts that were removed during subassembly. • Mount side support brace to threaded rod located on pole support assembly using a 5/16-18 Nylock nut • Mount side support brace to vehicle using H” x 1” Hex head lag bolts. A 3/16” pilot is required. Note: When mounting side support brace to flo

Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes! Use hardware provided with install kit /-20 x /” Hex head bolt & /” Flat washer Spacer Bracket w/ /-20 x /” Hex head bolt & /” Flat washer Telescoping pole assembly Pole support assembly C-TCB-7-IMP-INST-12-04 SUB ASSEMBLY: 1. Confirm receipt of all hardware and components. 2. Install Chevrolet Impala Specific C-Series-IMP Consolidator® into vehicle using hardware and instructions provided. 3. Deter

The bottom of each guard is numbered, signifying its’ location. 2. Open door and hold the window guard up to the window door frame. NOTE: The angle at the bottom of the guard framework faces towards the outside of the car. The guard framework fits evenly around the window frame. 3. Mark a few holes at the top of the door frame using the pre-drilled holes on the guard framework as a guide. Note: Do not mark holes for the sides or bottom yet. 4. Remove window guard and drill holes as marked wi

Hold window guard up to the window frame, and while pushing down against the door window frame, mark mounting hole locations. Remove guard and drill out mounting holes with 1/8” drill bit. Attach guards with #10 X 1/2” sheet metal screws. FORD EXPLORER WINDOW GUARD POSITIONS MODEL WGI-F13 POSITION #1 DRIVERS SIDE PASSENGER DOOR F13-1 POSITION #6 PASSENGER SIDE PASSENGER DOOR F13-6 Consolidator' • Kwik-Raze’ • Collins Dynamics' • Kwik-Kit" PrisonerTransports • K-9Transports 75 Jack

. 2. Mount window guards: Note: window guards have holes around perimeter for permanent mounting. These holes are not used with hinge kit. They also come flat in shipping. The guard must be pre-bent (outward) so it fits tight against the door window frame. Do not use holes on side of window guard to mount with the hinge application! 1. Hold window guard with pre-assembled hinge and upper bracket onto window frame. 2. Make sure guard is centered on window. 3. Attach hinge to lower door panel

Determine location to obtain both. • With offset bracket positioned against flat surface, (i.e., console, divider wall, etc.), mark and drill 5/16” hole at location of bolt on offset bracket. • Bolt offset bracket to “flat surface” using a fender washer and 5/16” nut. • Bolt C-PED1612 to floor of vehicle using /” x 1” -1 /” hex head lag bolts, depending on particular vehicle application. • Mount optional laptop mounts (C-3090 series), monitor mounts (C-3522), keyboard mounts (C-3329) or tilt

Box 2099 • Warminster, PA 18974 • 800.524.9900 / 215.957.0720(P) • 215.957.0729 (F) C-AS-INST-11-06

Box 2099 • Warminster, PA 18974 • 800.524.9900 / 215.957.0720(P) • 215.957.0729 (F) C-AS-INST-11-06

Standard and Metric wrench set #20 and #15 Torx driver TRAK MOUNTED CONSOLE HARDWARE: QTY: DESCRIPTION: 8 '/4-20 X 3/”Hex Head Bolt 8 /” Flat Washer 6 /” Lock Washer 8 /-20 Hex Nut INSTALLATION: PART #: GSM33001 GSM31005 GSM31026 GSM30005 1. 2. 3. 4. 5. 6. 7. Remove inner front seat mounting bolts near transmission hump. Just loosen outboard bolts. Place Z - 20 x %” Hex head bolts into under side tracks of trak mount. Position trak mount in desired location before tightening

Place seat bracket on top of hump mount brackets and replace seat mount bolts. Slide console up to dash and secure to trak mount with 1/4” hardware. Unit is ready to accept equipment control heads. HUMP BRACKET MOUNTED CONSOLE HARDWARE: QTY: DESCRIPTION: PART #: 4 Z-20 x /” Carriage bolt GSM32000 4 1/4” Flat Nylon Retaining Washer GSM31322 4 Z-20 Hex Flange Serrated Nut GSM30023 INSTALLATION: 1. Remove front seat mounting bolts near transmission hump 2. Place Carriage bolts into slots