Reinstall upper louver assembly (see Figure 15, page 11) and branch support. Close lower louver door. Valve Cover Shield Switch Plate Screw (see Figure 20). Set the cable bundle between the burner bracket and outer casing, away from the burner. 5. Test to make sure the blower is working properly. 6. Reinstall upper louver assembly (see Figure 15, page 11) and close lower louver. Extension Cord Use extension cord if needed. The cord must have a three-prong, grounding plug and a three-hole recepta

Attach damper clamp so the minimum permanent flue opening will be maintained at all times. Area of Various Standard Round Flues Diameter (ins.) Area (sq. ins.) 5" 6" 7" 8" 20 sq. inches 29 sq. inches 39 sq. inches 51 sq. inches Chimney Height (ft.) Minimum Permanent Flue Opening (sq. ins.) 6' to 15' 15' to 30' 39 sq. inches 29 sq. inches Damper Damper Clamp Damper Clamp Damper Damper Masonry Fireplace Manufactured Fireplace Figure 10 - Attaching Damper Clamp 14 INSTALLING Continued INSTALLING HE

— Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. — WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. — Installation and service must be performed by a qualified installer,

This makes the front of fireplace flush with wall. An optional trim kit accessory is available (see Accessories, page 30). Trim will extend past sides of fireplace approximately 1/2 inch. This will cover the rough edges of the wall opening. If installing a built-in mantel above the fireplace you must follow the clearances shown in Figure 11, page 12. Follow the instructions below to install the fireplace in this manner. Actual Framing Height 26" 26 7/8" Front Width 26 3/4" 26 7/8" Depth 9 1/2" 1

7. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Note: If pilot goes out, repeat steps 3 through 7. This fireplace has a safety interlock system. Wait one (1) minute before lighting pilot again. 8. Turn control knob counterclockwise to desired heating level. The main burner should light. Set control knob to any heat level between HI and LO. CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve. Ignitor Button

Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. IMPORTANT: Operating heater where impurities in air exist may create odors. Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These fumes may mix with combustion air and create odors. OBSERVED PROBLEM POSSIBLE CAUSE REMEDY Heater produces a clicking/ticking noise 1. Metal expanding while heating or con1. This is common w

INSTALLATION OPTIONS There are three options for mounting this heater. A. Mounting heater to wall B. Mounting heater to optional hearth base C. Mounting heater to optional mantel (some mantels require the hearth base) A. MOUNTING HEATER TO WALL Mounting Bracket The mounting bracket is located in the package tray. Remove mounting bracket from tray. Methods For Attaching Mounting Marking Screw Locations 1. Tape mounting bracket to wall where heater will be located. Make sure mounting bracket is le

Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies. Do not place clothing or other flammable material on or near the appliance. Never place any objects on the heater. Surface of heater becomes very hot when running heater. Keep children and adults away from hot surface to avoid burns or clothing ignition. Heater will remain hot for a time after shutdown. Allow surface to cool before touching. Carefully supervise young children when they

WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life. — Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. — WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supp

— Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. — WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. — Installation and service must be performed by a qualified installer,