No pretense here. Just all the variety, durability, and performance you need to get the job done. It’s as simple as that. Club-quality equipment that’s built to last. These machines deliver the kind of free weight workout your body craves. Don’t let the equipment you use limit your strength-training regimen. Get the equipment that works just as hard as you do. With the Free Weight Smith System and a full range of specialized workout stations to choose from, you can’t go wrong with ParaBody. SMIT

Make sure the Cable Trap and Finger Guards are oriented as shown. 27 28 29 30 66 99 62 66 90 26 109 111 77 63 99 68 90 66 29 66 70 109 64 66 109 66 99 99 90 25 63 109 63 5 80 68 90 15 31. Attach the end of the Press Cable (109) to a “U”- bracket (50) with an M8 Washer (98) and an M8 Nylon Locknut (91). Note: Do not completely tighten the Locknut; it should be tightened so that only two threads of the Cable show past the Locknut, as shown in the inset drawing. 33. Wrap the Butterfly Cable (106) o

BOLT, two (2) 5/16 IN. S.A.E. WASHERS, one (1)5/16 IN. LOCK WASHER, and one (1)5/16 IN. NUT. • Route the LEG CURL/EXTENSION CABLE as shown on drawing. (ALSO SEE VIEW B-B) • Run the LEG CURL/EXTENSION CABLE through the pre-determined hole of the D-RING as shown in (DETAIL A) and attach one (1) D-RING CABLE CLIP around the ball end of the LEG CURL/EXTENSION CABLE. 2. Attach one (1) SHOCK CORD to the D-RING CABLE CLIP on the end of the LEG CURL/EXTENSION CABLE as shown in (DETAIL A). 3. Route t

See FIGURE 1. • Remove the bottom of the front SHROUD & rear SHROUD by removing the four 3/8” X 1” BUTTON HEAD CAP SCREWS. See !IMPORTANT! • IF THE 832 LEG PRESS OPTION IS INSTALLED PROCEED TO PAGE 14. • IF THE 445 WEIGHT STACK OPTION IS INSTALLED PROCEED TO PAGE 27. • IF THE 832 LEG PRESS OPTION & 445 WEIGHT STACK OPTION ARE INSTALLED PROCEED TO PAGE 35. • IF NO OPTIONS ARE INSTALLED CONTINUE TO PAGE 3. 2 STEP 3 • Remove the three 1/4” CAP NUTS and each TENSION CORD from the TOP BOOM

• Route the LAT CABLE (99) as shown in FIGURE 33. (Remove pulleys for ease of installation.) • Run the LAT CABLE (99) through one of the holes in the D-RING (7) and attach one KEYHOLE CLEVIS (66) to the end of the LAT CABLE (99). See FIGURE 36 . • Replace and SECURELY tighen the FRONT UPRIGHT (25) and TOP BOOM (17) connection and any pulleys from the previous step. (NOTE: Make sure the LAT CABLE runs over the top of the bolts in the top boom.) NOTE: REMOVE BOLTS FOR CABLE INSTALLATION 25 17 99 7

Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your Parabody customer service representative at (800) 328-9714. There is a risk assumed by individuals who use this type of equipment. To minimize risk, please follow these rules: 1. Inspect equip

CABLEASSEMBLY (90) through openings in BASE (10) as shown in FIGURE 1. • Securely assemble two 3-1/2" PULLEYS (79) into BASE (10) using two 3/8 X 2-3/4" BOLTS (38), four 3/8" FLANGE SPACERS (66), and two 3/8” LOCKNUTS (48). (NOTE: Make sure LEG EXT. CABLE ASSEMBLY (90) is routed under PULLEYS and BOLTS.) • Slide LEG EXT. CABLE ASSEMBLY (90) through the opening in the end of the BASE (10) as shown in FIGURE 1. • Insert four 3/4" FLANGE BEARINGS (69) into tubes on REAR UPRIGHT (16) as shown in

Make sure that the word SCAN does not appear. To view both the elapsed time and your pace, press the center button until the word SCAN reappears. The lower section of the large display will show your pedaling speed and the resistance level. The display will change from one number to the other every few seconds. To view only your pedaling speed or the resistance level, press the lower button on the left side of the large display until only the word SPEED or RESISTANCE appears. Make sure that the

The left indicator will show your actual exercise pace, and the right indicator will show the current target pace. During the program, the target pace will periodically change; as the right indicator changes in height, simply adjust your pace so that both indicators are at the same height. Important: The target pace is a goal pace. Your actual pace may be slower than the target pace, especially during the first few months of your exercise program. Make sure to exercise at a pace that is comforta

This product must be assembled on a flat, level surface to assure its proper function. * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your Parabody customer service representative at (800) 328-9714. There is a risk assumed by individuals who use this type of equipment. To minimize risk, please follow these rules: 1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately. Fai