English 7 Day Programmable INSTALLATION5 MINUTE M T W T F S S Owner’s Manual Model 44905 Form# 44050-01 20100603 ©2010 Hunter Fan Co. English 7 Day Programmable INSTALLATION5 MINUTE M T W T F S S Table Of Contents At A Glance Know Your Thermostat 3 Setup Setting Day, Time, and System 8 Scheduling Scheduling Introduction 10 Setting Your Schedule 12 Temporary Temperature Change 18 Turning Off Scheduling 20 Home Today 22 Save Away 24 Features Alerts 26 Menu Options 30 Advanced Menu Options 34 Energ

Do not connect a cable to the Loop BNC unless it is connected to another terminated device because it will cause poor quality video. Connecting Audio Note It is your responsibility to determine if local laws and regulations permit recording audio. Figure 2-4 Audio In and Out Connectors AUDIO IN 1 AUDIO IN 2 AUDIO IN 3 AUDIO IN 4 AUDIO OUT Your DVR can record audio. 1. Connect the audio source to Audio In. 2. Connect Audio Out to your amplifier. Note The DVR does not have amplified audio output,

Disconnect all sources of power before servicing. Control unit and associated equipment may be damaged by removing and/or inserting cards, modules, or interconnecting cables while the unit is energized. Do not attempt to install, service, or operate this unit until manuals are read and understood. CAUTION - System Re-acceptance Test after Software Changes: To ensure proper system operation, this product must be tested in accordance with NFPA 72 after any programming operation or change in site-s

Password: admin. (administrator, local and network) • Username: 888888. Password: 888888. (administrator, local only) • Username: 666666. Password: 666666(Lower authority user who can only monitor, playback, backup and etc.) • Username: default. Password: default(hidden user) You can use the USB mouse, front panel, remote controller or keyboard to input. About input method: Click or press Shift on the front panel to switch between numbers, English character (small/capitalized) and denotation. No

Overlay mode: There are two options: preview and encode. Preview means overlay the card number in the local monitor video. Encode means overlay the card number in the record file. Overlay Position: Here you can select the proper overlay position from the dropdown list. Figure 5-32 Text Overlay(COM Type) Network Type The network type interface is shown in Figure 5-33. Here we take the ATM/POS protocol to continue. There are two types: with or without the protocol according to client’s requirement

• In General interface please input upload interval. • In Detect interface please enable snapshot function for specified channels. Or in alarm interface please enable snapshot function for specified channels. Please refer to the following figure for detailed information. Figure 4-14 Activation Snapshot Setting Priority Please note the activation snapshot has the higher priority than schedule snapshot. If you have enabled these two types at the same time, system can activate the activation snapsh

Mating wet components may cause damage not covered by the warranty. 10 - 5 Charging a Spare Battery The base can also charge a second battery while the terminal is positioned in the base. The second battery can be inserted in the battery charging well in back of the terminal connection. Place the battery in the well with the label facing up and toward the back of the unit. Angle the battery as shown. Once the connectors engage, the LED lights. If the LED is red, the unit is charging; if it is gr

2 On-Screen Compass Allows On-Screen control of a PTZ camera. 3 RS-232 / RS-485 Defines how to send the PTZ signal to the camera. 4 Select Camera Selects the current camera to be edited. 5 Port Settings Defines the specific settings to transmit to the PTZ. 6 Enable Pan/Tilt Enables the DVR to control the PTZ camera. 7 Preset and Tour Used to create Presets and Tours for the PTZ camera. Since each camera creates these in a different way, there can be multiple methods. 8 Protocol Selects the proto

Note: The alert is also triggered when you undo the cover to replace batteries in the door camera. MIC volume [For future use] The topmost control along the side (see diagram on page 8) will control the volume produced from a microphone. Adjust for optimum listening level. Scan button When used in a multi-camera system, this button scans through available pictures. Privacy Remember that this product uses the public airwaves, and that the 30-second duration video signal from the door camera(s) ca

Before you mount the door camera or receiver in a permanent place, make sure that you have tested the two units and that the system works in the location you have chosen! (See ‘Setting up’, beginning on the next page.) THE VISIOCAM SYSTEM Your Honeywell wireless video entry system uses radio signals to transmit a video picture of the caller from the door camera to the receiver. The system is expandable, so you can install additional surveillance cameras, or a second door camera if required. CHEC