(2)\a.jpg Hardware Pack F:\..... (2)\c.jpg F:\..... (2)\b.jpg Connecting Bolt X 37 Connector Housing X 37 Shelf Support (nog) X 8 Screw X 8 Controllers IR (Infrared) Remote Control RF (Radio Frequency) Remote Control 3-way Wall Switch (RJ45 Connection) AA Batteries Required Tool C:\Users\Eric\Desktop\....jpg Phillips Head Screwdriver Use of connecting bolts when assembling the components Step1: Use a Phillips Head Screwdriver to attach the Connecting Bolt to the furniture components (unit-A). St

Make sure the brackets are facing the front of the stand. 7. Attach the Holders (j) to the side legs and secure with M6x35 screws (n), M6 washers (q) and M6 nuts (o). (j) holder f (m) M6x20 (i) Bracket d1 d2 b c a (n) M6x35 5 Rev.052411.AS info@elitescreens.com 8. Attach the Projector Rail (g) to the Center Upright Bar (e) and secure with M6x15 screws (l), M6 washers (q) and M6 nuts (o). 9. Attach the Center Upright Bar (e) to the Middle Center Bar (d2) and to the Top Center Bar, and secure with

Please make sure that no other objects such as power switches, outlets, furniture, ladders, windows, etc. occupy the space designated to hang the screen. 2. Regardless if the screen is installed inside or on the wall, make sure that the proper mounting anchors are used and that the weight is supported appropriately by a strong and structurally sound surface just as any large and heavy picture frame should. (Please consult a home improvement specialist for the best advice on installation.) 3. Fra

Please follow the pre-cautions below for proper care procedures and to prolong the life of your StarBright7. Failure to comply will result in voiding your warranty. Avoid using any chemical compounds or harsh abrasives which will result in permanently damaging the screen material. • USE ONLY a soft non-abrasive cloth with mild soap and water to clean the screen material • DO NOT rub the cloth with force when cleaning to avoid permanently scratching the surface • DO NOT touch the screen surface w

Please follow the instructions in this package. With proper care, your QuickStand screen will provide many years of reliable service. Two Section Frame (For presentation screens that are less than 120” in diagonal measurement) 1. Take the frame out of the case and remove its wrappings. Unfold the main joints as shown in (fig 1). 2. Once the main joints are unfolded, make sure that the snap latches “click” into the locked position. The frame should now be fully elongated as in (fig2). *Note: The

Frame Parts x 6 pcs (4 top/bottom frame pcs. + 2 side frame pcs) 2. Tension Rods x 6 pcs (4 top/bottom rods + 2 side rods) 3. Screen Material x 1 pc 4. Center joints x 2 pcs 5. Elbow Joints x 4 pcs 6. Wall brackets x 2 – 3 pcs (depending on model/size) 7. Screws x 16 pcs 8. User Guide x 1 pc 9. Center Support Bar x 1 – 2 pc s (depending on model/size) 10. Support joiner x 2 – 4 pcs (depending on model/size) 11. Fix Plates x 30 – 90 pcs (depending on model/size) 12. Black cloth backing x 1 pc (Ac

062310-JA info@elitescreens.com Kestrel Accessories Kestrel Accessories Qty 1 Radio Frequency Remote Control Qty 1 Infrared Remote Control Qty 2 AAA batteries Qty 1 Qty 1 Qty 1 5-12V Trigger Low Voltage 3-way IR “eye” Receiver Wall Switch IMPORTANT SAFETY NOTES 1. Please read this manual before use and follow the procedures specified: a. Please retain this manual for future reference. b. To avoid any damages to the screen, do not use any accessories or parts not recommended by Elite Screens. c.

093009.JA info@elitescreens.com Parts List for WhiteBoardScreen™ Parts List for WhiteBoardScreen™ Please make sure all parts listed are included before proceeding with installation a b c de f G and H are not actual individual parts included but configurations only by combining parts (d) and (e) with the butterfly screw g h Ijk Note: The WhiteBoardScreen™ Series eraser should only be used for the WhiteBoardScreen™. Parts List a. Qty 4 – Butterfly screw b. Qty 12 – Wall screw c. Qty 12 – Hollow wa

1. Frame Parts x 6 pcs (4 Top & Bottom frame pcs + 2 Side frame pcs) 2. Tension Rods x 6 pcs (4 Top & Bottom frame rods + 2 Side rods) 3. Screen Material x 1 pc 4. Center Joints x 2 pcs 5. Elbow Joints x 4 pcs 6. Wall Brackets x 2.3 pcs (depending on size) 7. Screws x 16 pcs 8. User Guide x 1 pc 9. Center Support Bar x 1.2 pcs (depending on size) 10. Support Joiner x 2.4 pcs (depending on size) 11. Fix Plates x 30.90 pcs (depending on size) 12. Black Cloth Backing x 1 pc (AcousticPro 1080 models

Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra Black Top Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens. Unapproved changes or modifications (except for cutting the power cord for hardwire installations) to this unit are prohibited and will void your warranty. For more information, please contact our Technical Support Department at (877) 511-1211 Ext. 604. • Please retain this user’s guide for futu