ENTER/EXIT PROGRAMMING MODE DEFAULT Country Mode = U.S. Country Mode = Belgium Country Mode = Britain Country Mode = Croatia Supports only the interfaces listed in the Country Mode feature description. Supports only the interfaces listed in the Country Mode feature description. Country Mode = Czechoslovakia Gryphon™ I GD4100 Country Mode Country Mode — continued ENTER/EXIT PROGRAMMING MODE Country Mode = Denmark Supports only the interfaces listed in the Country Mode feature description. Country

CONDITIONS Code = Interleaved 2/5 or Code 39 PCS = 0.90 Pitch angle = 0° Skew angle = 10° - 20° Tilt angle = 0° The curves show the minimum and maximum radial distance. 60 56 130 64 (in) 160 150 52 (cm) 140 120 110 100 90 80 36 32 40 44 48 28 70 0 55 60 65 70 75 80 85 90 95 100 105 110 115 (cm) 22 24 26 28 30 32 34 36 38 40 42 44 46 (in) 60 50 40 24 20 16 Max. Reading Distance Reading distance Focus Distance 120 125 68 170 72 180 48 50 130 52 Min. Reading Distance Figure 90 – Standard Model 0.30

The DX6400 master Fieldbus communicates with a remote host (for ex. remote PC connected via Internet) by means of a cable connected to the Fieldbus connector provided. It can be activated by a signal generated by the remote Host or by a physical presence sensor. The external signals (trigger, encoder) are connected to the master through the C-BOX 100. The master reader connects to the first slave reader of the system through the local Lonworks 9-pin female connector. Fieldbus models are provided

reserves the right to make modifications and improvements without prior notification. Datalogic shall not be liable for technical or editorial errors or omissions contained herein, nor for incidental or consequential damages resulting from the use of this material. Product names mentioned herein are for identification purposes only and may be trademarks and or registered trademarks of their respective companies. © Datalogic S.p.A. 2002-2006 821000631 (Rev. A1) CONTENTS GUIDE TO INSTALLATION ....

They are used together and they have the following significance: when a jumper is in the J1 position (see Figure above) pin 40 is connected to pin 27 (EXT TRIG+); a jumper in J2 position connects pin 20 to pin 28 (EXT TRIG-). If the jumpers are removed pin 20 and pin 40 are disconnected. Casella di testo: to EARTH GROUND (default) Casella di testo: to GND Casella di testo: floating Casella di testo: J2 Casella di testo: J1 2.5 PROFIBUS CONNECTIONS AND SETUP 2.5.1 Profibus Node Address Selection

D Datalogic shall not be liable for technical or editorial errors or omissions contained herein, nor for ncidental or consequential damages resulting from the use of this material. i Product names mentioned herein are for identification purposes only and may be trademarks and or egistered trademarks of their respective companies. r Datalogic S.p.A. 2005 - 2006 © 19/07/06 CONTENTS REFERENCES ..........................................................................................................

To define a new Hot Key, complete the following steps: 1. Enter the key combination to define a new Hot Key in the Enter Key textbox. 2. The Note displays important information indicating Hot Keys that should not be used. Product Reference Guide Falcon® Desktop Utility for Windows® CE Figure B-5. Add a New Hot Key Table B-6. Adding a New Hot Key Dialog Command Description Enter Key Enter the desired key combination in this text box to define a Hot Key. OK Select/tap OK to add the specified Hot K

Factory default settings are underlined. To make settings that are not provided in the chapter, you can design custom bar codes or use the Falcon Management Utility (FMU) to program the Falcon. Refer to Configuring the Falcon, on page 2-1. 1D Symbologies Symbologies and bar code setup parameters included in this appendix are: • "Predefined Defaults" on page G-3. • "Codabar" starting on page G-3. • "Code 39" starting on page G-5. • "Code 93" starting on page G-8. • "Code 128" on page G-10. • "EAN

4.8 CHANGING DEFAULT SETTINGS Once your reader is setup, you can change the default parameters to meet your application needs. Refer to the preceding paragraphs for initial configuration in order to set the default values and select the interface for your application. In this manual, the configuration parameters are divided into logical groups making it easy to find the desired function based on its reference group. The first four groups are for Standard Interface parameter configuration: RS232

Via Candini 2 40012 - Lippo di Calderara di Reno Bologna - Italy Gryphon™ Dx30/Mx30 Ed.: 09/2006 This manual refers to software version 3.1.0 and later ALL RIGHTS RESERVED Datalogic reserves the right to make modifications and improvements without prior notification. Datalogic shall not be liable for technical or editorial errors or omissions contained herein, nor for incidental or consequential damages resulting from the use of this material. Product names mentioned herein are for identificatio