. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. .. Changes or modifications not expressly approved by party responsible for compliance could void the user authority to operate the equipment. FCC Part 68 Registration This equipment complies with Part 68 of the FCC Rules. On the bottom of this equipment is label that contains, among other information, the FCC registration Number and Ringer equipment Number (REN) for the equipment. If re

However, due to differences between the individual PSTNs provided in different countries, the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point. In the event of problems, you should contact your equipment supplier in the first instance. This device is designed to work with the notified networks in all EC member states. Nevertheless, some of the network services in individual countries might not be supported, but they wil

(The above figure displays that Port 1, Port 5 & Port 9 are included in one VLAN Group.) b. Device (manages the HomePNA Switch) .. Device Name Specifies the full name of the switch. The default device name for this switch is untitled. It is changeable. ..IP Address Specifies the unique IP address of your LAN. Default: 192.168.168.168. It is changeable. ..Subnet Mask Specifies the Subnet Mask. Default: 255.255.255.0. It is changeable. ..Gateway Specifies the Gateway. Default: 0.0.0.0. It is chang

1. Make sure the computer is turned off before installing the device. 2. Remove the expansion slot cover from the computer. 3. Carefully slide the PCI modem card into an available PCI slot, applying even pressure to the card. Secure the card to the computer with the screw. (PCI slots are 85mm long and positioned 40mm from the PC’s rear panel. Generally there are several PCI slots side by side). 4. Plug one end of the telephone cable into the Modem line jack and another end into the telephone jac

Standardized jacks are used for these connections. This equipment should not be used on party lines or coin phones. 2. If this device is malfunctioning, it may also be causing harm to the telephone network; this device should be disconnected until the source of the problem can be determined and until repair has been made. If this is not done, the telephone company may temporarily disconnect service. 3. The telephone company may make changes in it's facilities, equipment, operation and procedures

-47 Transmit Statistics Tab Frames Transmitted Successfully Shows information of packets successfully sent. Frames Retransmitted Successfully Shows information of packets successfully sent with one or more reties. Frames Fail To Receive ACK After All Retries Shows information of packets failed transmit after hitting retry limit. RTS Frames Successfully Receive CTS Shows information of packets successfully receive CTS after sending RTS frame. RTS Frames Fail To Receive CTS Shows information of pa

V.42bis/V.42, MNP 2-5 data compression and error correction. AT command set. Fax Group 3, V.17 14400bps, V.29 9600bps Fax Service Class 1 compliant. SYSTEM REQUIREMENTS .. An IBM compatible PC or notebook computer with USB interface .. Running with Windows 98 .. Drivers and utilities provided with this product .. RJ11 cable for connecting to a phone plug .. USB cable for USB Fax/Modem connected to your computer .. Driver software loaded on your PC .. Data and/or fax communications software. HARD

Make sure the power switch of your External Fax Modem 56K is also set to off. 2. Connect the RS-232 cable to your External Fax Modem 56K with one end to the RS-232 port on the rear panel of the External Fax Modem 56K and the other end to the COM port of your computer. 3. Connect the provided power adapter to the AC IN port and the other end into a wall outlet. 4. Turn the Power Switch to ON and power on your computer. 5. Connect the telephone line to the RJ-11 Line port, connect the other end of

They come pre-loaded with an adhesive that is not limited in shelf life, and the termination procedure provides the ability to reheat and reposition the fibre in the termination process. This easyto- install field mount connector provides reliable performance in indoor and outdoor applications and has no internal splice. All 3M™ Hot Melt connectors can be terminated using the same 3M™ Hot Melt Termination Kit 6365/6361. 3M™ LC Connectors require the 3M™ LC Expansion Kit 6650-LC which includes a

User Select Enable this function to select the country you are now locating. Fragmentation Threshold The mechanism of Fragmentation Threshold is used to improve the efficiency when high traffic flows along in the wireless network. If your 802. Wireless LAN Adapter often transmit large files in wireless network, you can enter new Fragment Threshold value to split the packet. The value can be set from 256 to 2346. The default value is 2346. RTS/CTS Threshold RTS/CTS Threshold is a mechanism implem