Оценок - 4, средний балл: 5 ( )

Производитель: Garmin Размер: 7.54 mb Название файла: Язык инструкции:

• Harbor mode—intended for use in inland waters, this mode works best with short-range radar signals (2 nm or less). • offshore mode—intended for use in open waters, this mode works best with long-range radar signals. • Sentry mode—allows you to put the radar into timed-transmit mode, in which you can configure a radar transmit and standby cycle to conserve power. You can also enable a guard zone in Sentry mode, which identifies a safe zone around your boat. Radar Mode Compatible Radar GMR 20, 21, 40, 41 GMR 18, 18 HD, 24, 24 HD GMR 404, 406 GMR 604 xHD, 606 xHD, 1204 xHD, 1206 xHD Cruising X X X Harbor X Offshore X Sentry X X X X Cruising Mode Cruising mode is the standard radar operation for the GMR 20, 21, 40, 41, 18, 18 HD, 24, 24 HD, 404, and 406 radar. NoTe: If you switch from Sentry mode to Cruising mode, the radar switches to full-time transmission and disables all guard zones. Showing Cruising Mode From the Home screen, select Radar > Cruising. A full-screen image of the gathered radar information appears. Your position is in the center of the screen, and the range rings . provide distance measurements. The distance between rings . and the radar range . are shown on the bottom of the screen. Cruising Mode . . . GPSMAP 700 Series Owner’s Manual 55 Radar Harbor Mode Harbor mode is the standard radar operation for use in inland waters, with a GMR 604 xHD, 606 xHD, 1204 xHD, or 1206 xHD radar. Harbor mode works best with short-range radar signals (2 nm or less). NoTe: If you switch from Sentry mode to Harbor mode, the radar switches to full-time transmission and disables all guard zones. Showing Harbor Mode From the Home screen, select Radar > Harbor. Harbor Mode Offshore Mode Offshore mode is the standard radar operation for use in open waters, with a GMR 604 xHD, 606 xHD, 1204 xHD, or 1206 xHD radar. NoTe: If you switch from Sentry mode to Offshore mode, the radar switches to full-time transmission and disables all guard zones. Showing Offshore Mode From the Home screen, select Radar > offshore. Offshore Mode 56 GPSMAP 700 Series Owner’s Manual Radar Sentry Mode Sentry mode allows you to put the radar into timed-transmit mode, in which you can configure a radar transmit and standby cycle to conserve power. You can also enable a guard zone in this mode, which identifies a safe zone around your boat and sounds an alarm when a radar object enters this zone. Sentry mode works with all Garmin GMR model radars. Showing Sentry Mode From the Home screen, select Radar > Sentry. Enabling Timed Transmit From the Home screen, select Radar > Sentry > Menu > Sentry Setup > Timed Xmit > on. Setting the Standby and Transmit Times You must enable timed transmit before you can set the standby and transmit times (page 57). To help conserve power, you can indicate the radar standby time and the transmit time to implement periodic radar signal transmissions at set intervals. 1. From the Home screen, select Radar > Sentry > Menu > Sentry Setup. 2. Select Stdby Time. 3. Enter the time interval between radar signal transmissions. 4. Select Done. 5. Select Xmit Time. 6. Enter the duration of each radar signal transmission. 7. Select Done. Enabling a Guard Zone From the Home screen, select Radar > Sentry > Menu > Sentry Setup > enable Guard Zone. Defining a Partial Guard Zone You must enable a guard zone before you can define the boundaries of the zone (page 57). You can define the boundaries of a guard zone that does not completely encompass your boat. 1. From the Home screen, select Radar > Sentry > Menu > Sentry Setup > Adjust Guard Zone > Move Guard Zone > Corner 1. 2. Touch and drag the location of the outer guard-zone corner ( ). 3. Select Corner 2. GPSMAP 700 Series Owner’s Manual 57 Radar 4. Touch the location of the inner guard-zone corner. 5. Select Done. Defining a Circular Guard Zone You must enable a guard zone before you can define the boundaries of the zone (page 57). You can define a circular guard zone that completely encompasses your boat. 1. From the Home screen, select Radar > Sentry > Menu > Sentry Setup > Adjust Guard Zone > Move Guard Zone > Circle. 2. Touch and drag the location of the outer guard-zone circle, ( ). 3. Select Corner 2. 4. Touch and drag the location of the inner guard-zone corner. 5. Select Circle. Setting the Safe-zone Collision Alarm See “Setting the Safe-zone Collision Alarm (page 15). Viewing a List of AIS Threats From any radar view or the Radar Overlay, you can view and customize the appearance of a list of AIS threats. 1. From the Home screen, select Radar. 2. Select Cruising, Harbor, offshore, Sentry, or Radar overlay. 3. Select Menu > other Vessels > AIS List. 58 GPSMAP 700 Series Owner’s Manual Radar Showing AIS Vessels on the Radar Screen AIS requires the use of an external AIS device and active transponder signals from other vessels. You can configure how other vessels appear on the Radar screen. If any setting (except the AIS display range) is configured for one radar mode,...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: