Оценок - 2, средний балл: 5 ( )

Производитель: Louisville Tin and Stove Размер: 731.33 kb Название файла: Язык инструкции:

Immediately call a qualified service • Do not touch any electric switch; do not technician to inspect the appliance and to use any phone in your building. replace any part of the control system and any • Immediately call your gas supplier from a gas control which has been under water. neighbor’s phone. Follow the gas supplier’s instructions. OPERATING INSTRUCTIONS 1. STOP! Read safety information on this label. 2. Set the thermostat to the lowest setting. 3. Turn off all electric power to the appliance. 4. This appliance is equipped with an ignition device which automatically lights the burner. Do not try to light the burner by hand. 5. Turn gas control knob clockwise to “OFF”. Do not force. 6. Wait five (5) minutes to clear out any gas. If you smell gas, STOP! Follow “B” in safety information on this label. If you don’t smell gas, go to next step. 7. Turn gas control knob counterclockwise to “ON”. 8. Turn on all electric power to the appliance. 9. Set thermostat to desired setting. 10. If the appliance does not operate, follow instructions “To Turn Off Gas To Appliance” and call your service technician or gas supplier. 1. Set the thermostat to lowest setting. 2. Turn off all electric power to the appliance if service is to be performed. 3. Turn gas control knob clockwise to “OFF”. Do not force. TO TURN OFF GAS TO APPLIANCE Page 12 Gas control knob shown in “OFF” position NATURAL GAS WOW253 1.3 5 5 5 6 5 6 5 7 WOW403 5 4 5 5 5 5 5 6 5 6 L.P. GAS WOW254 6 7 6 8 6 9 7 0 7 0 WOW404 6 6 6 8 6 8 6 9 7 0 MODEL 0 to 2,000’ 4,000’ 6,000’ 8,000’ - NO. 2,000’ 4,000’ 6,000’ 8,000’ 10,000’ PROPER BURNER FLAME Appliance input ratings are based on sea level operation and need not be changed for operation up to 2,000 (609.9m) elevation. For operation at elevations above 2,000 ft. (609.9m), manufactured to specified deration conditions for Canada and the United States, use the following orifice chart for/to determine the correct orifice DMS for a specific elevation. Page 13 SPECIFIC ELEVATIONS HIGH ALTITUDE BURNER ORIFICING Appliance input ratings are based on sea level operation and need not be changed for operation up to 2,000 ft. (609.9m) elevation. For operation at elevations bove 2,000 ft. (609.9m), manufactured to specified deration conditions for Canada and the United States. Use the following orifice chart for/to determine the correct orifice DMS for a specific elevation. BLOCKED VENT SHUT-OFF SYSTEM This heater is equipped with a blocked vent shutoff system that will automatically turn the heater off in the advent of the vent exhaust or air intake pipe becoming blocked. This blockage may be caused by snow accumulation, insects, small animals, animal nest, etc. Once this occurs the heater will remain in a lockout cycle for one hour. After one hour there will be an ignition attempt. If the blockage has been removed, the heater will return to normal operation. If the blockage remains, the heater will return to a one hour lock out cycle. If this problem occurs, homeowners must not attempt to operate or repair the heater themselves but contact a qualfied service agency. There is no primary air adjustment on the burner and with correct installation, a proper flame is assured; since the correct manifold pressure and orificing has been done at the factory for elevations up to 2,000 ft. FIGURE 14 LIGHT BLUE OUTER MANTLE DARKER BLUE INNER MANTLE FIGURE 13 - - WOW403 / WOW404 BURNER BOX GAS VALVE SIGHT GLASS SIGHT GLASS BURNER BOX MANIFOLD FIGURE 13 - - WOW253 / WOW254 After conversion is complete, attach P/N 91137 Label adjacent to the rating plate. Page 14 GAS CONVERSION This heater is field convertible. Use only factory supplied, certified kits. Model Conversion Number Description Kit No. WOW253 Convert Nat. to L.P. 20,000 49670 WOW254 Convert L.P. to Nat. 20,000 49660 WOW403 Convert Nat. to L.P. 40,000 49690 WOW404 Convert L.P. to Nat. 40,000 49680 CAUTION: Only qualified installers or service agency are authorized to make a gas conversion on this heater. ORIFICE CONVERSION A.) Turn thermostat to “OFF” or lowest setting. B.) Allow heater to cool. Remove front panel. C.) Turn off electric power to heater. D.) Turn off gas supply. E.) Disconnect gas supply line from gas control. F.) From outside, remove six (6) screws securing back of outer cabinet to air intake and exhaust flanges. G.) From inside, gently slide combustion tube assembly forward and out of outer cabinet. H.) Disconnect gas control wires and remove right side of inner cabinet. I.) Remove two screws securing gas control bracket to burner box. J.) Remove six (6) screws securing manifold to burner box. K.) Pull manifold/gas control assembly out of burner box. L.) Replace burner orifices with orifices of correct size for type of gas and elevation. NOTE: The WOW403, 404 requires 5 orifices and the WOW253, 254 requires 3. M.) Carefully check integrity of all gaskets, make sure all gaskets are in place. N.) Re-assemble heater by reversing Steps K - F. CONVERTING GA...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: