Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
10. Keep propane tank(s) below 38° C (100° F). 11. Check heater for damage before each use. Do not use a damaged heater. 12. Check hose before each use of heater. If highly worn or cut, replace with hose specified by the manufacturer before using heater. 13. Locate heater on stable and level surface if heater is hot or operating. 14. Not intended for use on finished floors. 15. Never block air inlet (bottom of combustion chamber) or air outlet (glowing combustion chamber) of heater. 16. Keep heater away from strong drafts, wind, water spray, rain or dripping water. 17. Do not leave heater unattended. 18. Keep children and animals away from heater. 19. Never move, handle or service a hot or operating heater. Severe burns may result. Wait 15 minutes after turning heater off. 20. To prevent injury, wear gloves when handling heater. 21. Never attach duct work to heater. 22. Do not alter heater. Keep heater in its original state. 23. Do not use heater if altered. 24. Turn off gas supply to heater when not in use. 25. Use only original replacement parts. This heater must use design-specific parts. Do not substitute or use generic parts. Improper replacement parts could cause serious or fatal injuries. PRODUCT IDENTIFICATION Figure 1 - Product Identification Top Cover Lighting Port Combustion Chamber Control knob Protective Screen UNPACKING 1. Remove all packing items applied to heater for shipment. Keep plastic cover caps (attached to valve inlet and hose/regulator assembly) for storage. 2. Remove all items from carton. 3. Check all items for shipping damage. If heater is damaged, promptly inform dealer where you bought heater. THEORY OF OPERATION The Fuel System: For propane units, the hose/ regulator assembly attaches to the propane gas supply. For natural gas units, the gas supply attaches to the heater through user supplied hose or pipe. This provides fuel to the heater. The Ignition System: The piezo ignitor lights the burner fuel supply. TheAutomatic Control System: This system causes the heater to shut down if the flame goes out. 114248-01B GAS SUPPLY PROPANE/LP GAS MODEL 125-R ONLY Propane gas and propane tank(s) are to be fur nished by the user. Use this heater only with a propane vapor withdrawal supply system. See Chapter 5 of the Standard for Storage and Handling of Liquefied Petroleum Gas, ANSI/NFPA 58 and/or CAN/CGA B149.2. Your local library or fire department will have this booklet. The amount of propane gas ready for use from propane tanks varies. Two factors decide this amount. 1. The amount of liquid propane gas in tank(s) 2. The temperature of tank(s) The chart below shows the minimum number of 45 kg (100 lb) tanks needed to run the heater. Connect tanks together with a manifold. Average Temperature Number Of Tanks °C (°F) At Tank Location 45 kg (100 lb) 4° (40°) to 0° (32°) 2 Below 0° (32°) 3 Less gas is vaporized at lower temperatures. Your local propane gas dealer will help you select the proper supply system. NATURAL GAS MODEL 125-RN ONLY The user must furnish the natural gas supply and the connections to the heater. Regulate the natural gas supply down from a minimum 7" w.c. to a maximum of 1/2 psi. The natural gas supply capacity should be able to supply a minimum of 125 cubic feet of gas at pressure for each heater connected to the system. Consult your natural gas supplier for proper sizing of the natural gas supply lines. Follow all local ordinances and codes. In the absence of local ordinances and codes, refer to the National Fuel Gas Code Handbook, NFPA54/ANSI Z223.1 andthe NaturalGasInstallationCode,CAN/ CGA B149.1. VENTILATION WARNING: Provide at least a .35 m2 (3.75 ft2) opening of fresh, outside air while running heater. If proper fresh, outside air ventilation is not provided, carbon monoxide poisoning canoccur. Provide proper fresh, outside air ventilation before running heater. INSTALLATION INSTRUCTIONS Read these instructions carefully. Read and adhere to these instructions. Do not allow anyone who has not read these instructions to assemble, light, adjust or operate this heater. Do not attempt to operate the heater with any gas other than that indicated on the heater nameplate. For the U.S. and/or Canada, the installation of this appliance must comply with local and/or Provincial codes or, in the absence of these codes, with the (U.S.) National Fuel Gas Code, ANSI Z223.1 – Latest Edition (for natural and propane/LP gas operation) and with the (U.S) Standard for the Storage and Handling of Liquefied Petroleum Gases, ANSI/NFPA 58 (for propane/LP gas operation) or with the current (Canadian) CAN/CGA B149.1 and B149.2 installation codes. This heater (including hose and regulator assembly if applicable) must be inspected before each use and at least annually by a qualified service person. If the hose for model 125-R shows evidence of excessive abrasion or wear or if the hose is cut, it must be replaced prior to the heater being put into operation. The replacement...