Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Read and follow the instructions provided with any tools listed here. 20 lb LP Gas Models Tools Needed ¦ Tape measure ¦ Wrench or pliers ¦ Small, flat-blade screwdriver ¦ Pipe wrench ¦ Flat-blade screwdriver ¦ Scissors or cutting pliers (to remove tiedowns) ¦ #2 and #3 Phillips screwdriver ¦ Noncorrosive leak- ¦ Level detection solution Parts Supplied ¦ Gas pressure regulator/hose assembly set for 11" WCP LP gas (attached to manifold) ¦ 1 single-prong plug/5,000 mAmp transformer assembly ¦ Convertible regulator set for 4" WCP Natural gas ¦ Orifices for Natural gas conversion ¦ LP gas fuel tank tray Parts Needed ¦ 20 lb LP gas fuel tank - approximately 18" (45.7 cm) height and 12" (30.5 cm) diameter Natural Gas Models Tools Needed ¦ Tape measure ¦ Wrench or pliers ¦ Small, flat-blade screwdriver ¦ Pipe wrench ¦ Flat-blade screwdriver ¦ Scissors or cutting pliers (to remove tiedowns) ¦ #2 and #3 Phillips screwdriver ¦ Noncorrosive leak- ¦ Level detection solution Parts Needed ¦ Gas line shutoff valve ¦ ." male pipe thread nipple for connection to pressure regulator ¦ LP gas-resistant pipe-joint compound ¦ CSA design-certified outdoor flexible stainless steel appliance connector (4-5 ft [1.2-1.5 m]) or rigid gas supply line as needed. Parts Supplied ¦ Convertible regulator set for 4" WCP Natural gas. ¦ Single-prong plug/5,000 mAmp transformer assembly Location Requirements Select a location that provides minimum exposure to wind and traffic paths. The location should be away from strong draft areas. Do not obstruct flow of combustion and ventilation air. Clearance to combustible construction for built-in outdoor side burners: ¦ A minimum of 24" (58 cm) must be maintained between the sides and back and any combustible construction. ¦ A zero clearance may be maintained below the cooking surface and any combustible construction. Ignition A grounded, 3-prong outdoor GFI outlet is to be located inside the island cabinet and to the left of the side burner. See “Electrical Requirements” section. Product Dimensions Style 1 -Front to Back Built-In Dual Side Burners A B C D E F H G A. 13" (33 cm) E. 25..." (64.5 cm) B. 10..." (27 cm) F. Manifold pipe C. 17" (43.2 cm) G. 4..." (11.1 cm) D. 26..." (67 cm) H. 22..." (57.8 cm) Style 2 - Side by Side Built-In Dual Side Burners A C B D E F A. 24" (61 cm) B. 10..." (27 cm) C. 28" (71.1 cm) D. 20..." (52.1 cm) H E. 19..." (49.5 cm) F. Manifold pipe G. 4..." (11.1 cm) H. 17" (43.2 cm) G Built-In Outdoor Side Burner Enclosure This built-in outdoor side burner is for installation in a built-in enclosure constructed of combustible and non-combustible materials. Some types of non-combustible materials could be brick, firewall or steel. Some types of combustible materials could be wood or laminate. The enclosure for the built-in outdoor side burner is to be a minimum of 11" (28.0 cm) high x 23" (58.4 cm) deep x 14" (35.6 cm) wide for front to back model and 11" (28.0 cm) high x 17" (43.2 cm) deep x 25" (63.5 cm) wide for side by side model. Cabinet Dimensions Counter or support surfaces must be level. The installation of this side burner must conform with local codes or, in the absence of local codes, with either the National Fuel Gas Code, ANSI Z223.1/NPFA 54, Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code, B149.2. Copies of the standards listed may be obtained from: CSA International 8501 East Pleasant Valley Rd. Cleveland, Ohio 44131-5575 NOTE: The outdoor side burner drops into the enclosure opening and is supported by its side flanges. No bottom support is needed. The dimension chart and illustration below include cutout dimensions and minimum spacing requirements for all built-in outdoor products. The illustration is for reference. The design of your cabinet layout can be personalized, but the dimensions for the cutouts and minimum spacing must be followed. C E D H A G K K F K B J D E 20..." (52.4 cm) 1..."(3.8 cm) min. 3" (7.6 cm) min.to open hood 2..." (6.4 cm) min. 12" (30.5 cm) min.to any accessory 12" min.to anyaccessory 20..." (53.0 cm) 9..."(23.2 cm) 5"(12.7 cm) min. C M L K K Grills orRefreshment Centers SideorSearBurners WarmingDrawer Access Doors Refrigerator orIce MakerUtilityorTrashDrawer Minimum Spacing Requirement Between Cutouts -Dimension K Between 2 or more sets of Access Doors adjacent to each other: K = 14" (35.6 cm) when 2 adjacent doors are opened to 90 degrees K = 8" (20.3 cm) when 1 of the adjacent doors is opened to 90 degrees Between a set of Access Doors and a Trash Drawer, Utility Drawer, Warming Drawer, Refrigerator, or Ice Maker: K = 8" (20.3 cm) when 1 of the adjacent doors is opened to 90 degrees Between a Trash Drawer, Utility Drawer, or Warming Drawer: K = 3" (7.6 cm) Cabinet Height and Depth Dimensions Dimension A Minimum Dimension B Minimum With outdoor refrigerator 37" (94.0 cm) 26" (66.0 cm) Grill with insulated jacket 36." (92.7 cm) 27" (68.6 cm) Grill without insulated jacket 35." (90.2 cm) 26" ...
Эта инструкция также подходит к моделям:Газовые горелки - KBZU122VSS (982.06 kb)
Газовые горелки - W10176789A (982.06 kb)