Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
Secure with one hand knob (F) and belleville washer (G). See figure 4. NOZZLE (N) FIGURE 4 UPPER HANDLE (O) 2. Place the upper handle (0) in position over lower handle. Fasten with four hex bolts (I) and lock nuts (J) provided. See figure 5. Two 7/16" wrenches are required. FIGURE 5 3. Place the stud pins (K) in holes in upper handle (head of pins go to the inside of handle). Secure pins with push-on speed nuts (L) by holding speed nut with box wrench and tapping pin with hammer. See figure 6. 5 I HAND KNOB (F) Place air duct assembly (P) over opening on top of housing. Secure with two hand knobs (F) and belleville washer (G). See figure 7. FIGURE 7 BAG IT) Assemble the bag by slipping the top straps on bag (T) over upper handle. Hook two small straps over stud pins on handle. Slip elastic opening of bag over air duct assembly. See figure 8. NOTE Be certain elastic on bag is placed over the flanges on air duct assembly. FIGURE 8 X^CLUTC -i GRIP ASSEM 3LY (A) 6. CLEVIÎ. PIN (C) NOTE Steps 6, 7, 8 and 9 are for self-propelled units only. Assemble the clutch grip (A) to the left hand side of upper handle. Secure in place with clevis pin (C) and hairpin clip (B). See figure 9. Hear4' of clevis pin should be to the outside of handk FIGURE 9 6 LOCK NUT (E) EXTENSION SPRING (D) \ 7. Slide the extension spring (D) onto clutch rod (Q) as shown in figure 10. Thread lock nut (E) onto clutch rod approximately 2-1/2 inches. CLUTCH ROD (Q) FIGURE 10 CLUTCH BRACKET ASSEMBLY 8. Hook top (hooked end) of clutch rod into clutch grip. Hook spring into clutch bracket assembly. See figure 11. Spring should not have any slack. Adjust nut so that when the clutch grip is all the way up, there is no slack in the spring. 9. Thread hex jam nut (M) onto clutch rod, and lock it against the lock nut (E). FIGURE 11 HAND KNOB ASSEMBLY INSTRUCTIONS To Convert from a Vacuum to a Leaf Blower. FIGURE 12 Engine must be stopped (off) and spark plug wire disconnected. 1. Remove the bag. 2. Remove the air duct assembly by removing two hand knobs and belleville washers. 3. Remove the nozzle by removing one hand knob and belleville washer. -4. Remove the hand knob and belleville washer holding the housing to engine brace. See figure 12. 7 I FIGURE 13 5. Lift up and out on the housing and rotate it 105° clockwise. Chute opening should be to the riglr hand side when viewed from the front of unit. See figure 13. 6. Place the impeller guard (S) into flanges on front of housing. Line up hole in guard with hole on housing. Secure with one hand knob and belleville washer. See figure 13. HAND KNOB DIRECTIONAL DISCHAR3E ASSEMBLY (R) 7. Place the directional discharge assembly (R) ove> chute opening. Secure with two hand knobs and belleville washers. See figure 14. FIGURE 14 HEX NUT (W) TRUSS MACHINE SCREW (X), BELLEVILLE WASHER (AB) HEX J£M LOCK MUT (AC) HITCH PLATE SHOULDER SPACERS(V) HEX NUT (Z)' SHOULDER'' BOLT (AA) BELLEVIL _E WASHER (AB) FIGURE 15 ASSEMBLY INSTRUCTIONS for Tow Bar Kit (Optional) 1. Remove the self-tapping screws on each side of frame. Refer to drawing on page 12, reference number 42. 2. Place two bar halves in position on frame. Place one shoulder spacer (V) between frame and tow bar. Next, place shoulder spacer (V) and hex bo!t (U) through tow bar and frame. Secure with hex nut (W). See figure 15. Repeat for other side. 3. Secure the two tow bar ends together with truss machine screw (X), lock washer (Y) and hex nut (Z). See figure 15. To attach the tow bar to a hitch, place the shouldf bolt (AA) up through the tow bar. Place one bellevi^ washer (AB) on the shoulder bolt, then the hitch plate and the other belleville washer. Cupped side of the washers must be against the hitch plate. Secure with hex jam lock nut (AC). See figure 15. 8 OPERATION BEFORE STARTING ENGINE "Service engine with gas and oil. See engine manual acked with vacuum for complete instructions for care and maintenance of engine. READ DIRECTIONS CAREFULLY. A CAUTION REVOLVING BLADES-KEEP HANDS AWAY FROM ALL OPENINGS TO START ENGINE After the engine has been properly fueled and oiled (refer to engine operating and maintenance instructions), start engine following the instructions below. 1. Move choke lever on engine t...
Эта инструкция также подходит к моделям:Газоноуборщики - 240-675-000 (1.7 mb)
Газоноуборщики - 240-689-000 (1.7 mb)
Газоноуборщики - 240677 (1.7 mb)
Газоноуборщики - 240687 (1.7 mb)