Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Do not change grease; simply acid if necessary. MAINTENANCE A (*warnTng*J Disconnect spark plug wire and ground it against the engine before performing any repairs or maintenance. BELT REPLACEMENT (Self-Propelled Models Only) 1. Remove the nozzle or impeller guard from front of blower housing. 2. Remove hex bolt and lock washer from cen :er of impeller. See figure 18. A 9/16" socket wench with extension is needed. 3. Remove hand knob and belleville washer from top of housing. 4. Remove two self-tapping screws which hoi J the belt guard. See figure 19. A 3/8" wrench is required. Lift off belt guard. FIGURE 19 5. Slide belt off the impeller pulley. Slide housing and impeller off engine crankshaft. Be careful to not lose square key. See figure 20. FIGURE 20 10 6. Slide impeller and blower housing assemblies off crankshaft. \7. Remove belt from P.T.O. pulley and install new belt. See figure 20. ■¡^ NOTE When reassembling the new belt, the aid of another person will be helpful. 8. Turn the crankshaft until the key way on shaft is directly on top. While holding housing assembly and impeller assembly, line up the key way on the pulley with the key on the crankshaft, and slide housing and impeller assemblies onto crankshaft. 9. Secure impeller to crankshaft with hex bolt and lockwasher, removed in step 2. Tighten securely. 10. Slip belt over impeller pulley and reassemble the belt guard. 11. Secure blower housing with hand knob and washer. 12. Reassemble the nozzle or impeller guard. OFF-SEASON STORAGE The following steps should be taken to prepare the unit for storage. 1. Clean the engine and the entire unit thoroughly. 2. Refer to engine manual for correct engine storage instructions. 3. Store unit in a clean, dry area. NOTE When storing any type of power equipment in an unventilated or metal storage shed, care should be taken to rustproof the equipment. Using a light oil or silicone, coat the equipment, especially springs and bearings. TROUBLE SHOOTING CHART PROBLEM CAUSE REMEDY 1. Excessive vibration. A. Bent crankshaft. B. Vane plate out of balance. A. Replace crankshaft (should be done by an authorized service dealer). B. Replace vane plate. 2. Height adjustment slips out of lockout position. Handle bent. Replace index handle and index plate. 3. Engine fails to start. A. Check fuel tank for gas. B. Spark plug lead wire disconnected. C. Faulty spark plug. A. Fill tank if empty. B. Connect lead wire. C. Clean, adjust gap or replace. 4. Hard starting or loss of power. A. Spark plug wire loose. B. Dirty air cleaner. A. Connect and tighten spark plug wire. B. Clean air cleaner as described in engine manual. 5. Engine overheats. \ hi....................................... A. Carburetor not adjusted properly. B. Air flow restricted. C. Engine oil level low. A. Adjust carburetor. See engine manual. B. Remove blower housing on engine and clean as described in the engine manual. C. Fill crankcase with the proper oil. NOTE: For repairs beyond the minor adjustments listed above, please contact your local service dealer. 11 I Models 675, 685 and 689 ) ' с JW-вл-Г 12 Models 675,685 and 689 ^ PARTS LIST FOR MODELS 675, 685, 689, 240677 and 240687 POWER VACUUMS REF. NO. PART NO. COLOR CODE DESCRIPTION New Part REF. NO. PART NO. COLOR CODE DESCRIPTION New Part 1 05778 Clutch Grip Ass'y.t 41 715-0246 Spring Pin Spiral 3/16” Dia. 2 711-0679 Clevis Pin .375” Dia. x 1.88"t x 1.25" Lg.t 3 747-0154 Clutch Rod 32” Lg.t 42 710-0726 Hex Wash. Hd. "AB” Tap Scr. 4 749-0787 Handle Brace (Painted) 5/16" x .75" Lg. 749-0482 Handle Brace (Chrome) 43 Engine 5 Part of Engine 46 748-0201 Spacer .63 I.D. x .88" O.D. 6 710-0892 Hex L.-Wash. Hd. AB Tap Scr. x .56" Lg t 1/4” x .62” Lg.t 47 14530-638 Side Plate 7 14558 Belt Guardt 48 715-0247 Spring Pin Spiral 3/16” Dia. 8 714-0114 Square Key 1/4” x 2.0” Lg. x 1.0” Lg. t 9 14536A Air Vane Plate Ass'y. (675 and 49 748-0288 Drive Piniont 677) N 50 710-0170 Hex Locking Bolt 5/16-24 14557A Air Vane Plate Ass'y w/pulleyt x .62" Lg. 10 710-0442 Hex Bolt 5/16-18 x 1.5” Lg* 51 736-0159 Fl.-Wash. .34" I.D. x .87" O.D. 11 754-0219 ”V"-Beltt 53 734-1035 Wheel Ass'y.-Comp. 12” x 3” 12 736-0119 L.-Wash. ...
Эта инструкция также подходит к моделям:Газоноуборщики - 240-675-000 (1.7 mb)
Газоноуборщики - 240-685-000 (1.7 mb)
Газоноуборщики - 240677 (1.7 mb)
Газоноуборщики - 240687 (1.7 mb)