This plug is located at the right rear of body. 3. Remove the four control lever bolts and remove upper control levers (P/N 9079 A 9080). 4. Remove the two acorn nuts on floor of body and release latches on the rear of body near each side. 5. Place height adjustment lever in the vertical position, engage the parking brake and carefully lift body off the chassis. 6. Reverse above procedures to install body. Safety Checks - "Important" 1. After reassembly of body onto chassis and while seate

This will place the initial start up of the engine in a no load situation and allow complete engine lubrication. Adjustment; 1. Install engine to Mower deck drive belt (P/N 6111). 2. Check and adjust tire pressures. Front 19 to 21 psi; Rear 8 to 12 psi. Tires May have been over inflated for shipping purposes. 3. Place the Mower on a level surface. Using the lift handle, raise the Mower deck to a height which will allow Measurements to be taken from the surface to the tops of the two outer

The upper body can be folded forward to expose the transaxle. In some cases, it may be necessary to remove the upper body to service the transaxle. 2. To remove upper body, fold forward and remove bolt (P/N 3088) from cable CP/N 3780). Shut upper body and remove two bolts (P/N 3093) from the front of upper body hinge located on the brake shaft (P/N 9283). Disconnect seat switch (P/N 4047) at plug-in. 3. Reverse above procedure to reinstall. SEAT ADJUSTMENT 1. Raise upper body. 2. Loosen f

DO NOT operate Bower without seat adjustment knobs properly tightened. 4. Close upper body and push retention latch (P/N 3934) over transaxle backing plate. REMOVING THE BODY 1. The 312 has a (2) piece polyethelene body. The upper body can be folded forward to expose the transaxle. In some cases, it nay be necessary to remove the upper body to service the transaxle. 2. To relieve upper body, remove two bolts (P/N 3080) from the front of upper body hinge located on the brake shaft (p/N 92

27 SERVICE AIR FILTER & PRE-CLEANER - 18.5 & 21 HP ENGINES NOTE: Air filter configuration may differ from shown. Consult engine manual for further information. Interval: Pre-Cleaner: Every 25 hours or as required. Air Filter: Every 50 hours or as required. Replacement Interval: Pre-Cleaner: As required. Air Filter: Every 200 hours or once per season. Air Filter Removal & Installation 1. Lift up on the bottom of the latch (A, Figure 37 or 38) and flip the latch away from the cover. 2. Remove the

• Fill the fuel tank with fresh fuel. FUEL RECOMMENDATIONS For daily operation: Use only unleaded gasoline with a pump sticker octane rating of 87 or higher. Gasohol (up to 10% ethyl alcohol, 90% unleaded gasoline by volume) is approved as a fuel. Methyl Teriary Butyl Ether (MTBE) and unleaded gasoline blends (up to a maximum of 15% MTBE by volume) are approved as a fuel. Do not use unapproved gasolines, such as E85. Do not mix oil in gasoline or modify the engine to run on alternate fuels. This

It is mandatory to follow these instructions in order to prevent situations that could endanger the operator’s and other people’s safety, and to ensure the correct functioning of the shredder. If you have questions, call “FERRI” after-sales service or a specialized “FERRI” dealer. 1.2 Identifying the Machine Each shredder has an identification plate attached; the data necessary to identify the model and the serial number to order spare parts or after-sales service are both stamped on the plate (

IMPORTANT: Please fill out the SNAPPER Product Registration Card immediately and mail to: Snapper's Product Registration Center, P.O. Box 1379, McDonough, Georgia 30253 11 unit breakdown & parts list 12 unit breakdown & parts list S SSn nna aap ppp ppe eer rrZ ZZ- --V VVa aac ccB BBl llo oow wwe eer rrU UUn nni iit ttG GGr rro oou uup pp4 448 88” ””, ,,5 552 22” ””, ,,6 661 11” ””M MMo ood dde eel lls ss Item Part No. Qty Description 1 3046782 1 WELDMENT, Blower Belt Guard 2 91121 1 NUT, 1/2-13

A Main frame tire 2 (27" x 10 ." x 15") 2 (27" x 10 ." x 15") 2 (27" x 10 ." x 15") 2 (27" x 10 ." x 15") cast clevis hitch is standard and a 2 5/16" ball hitch is optional for road transport. The 5Blades per deck / overlap 3 blades / 1 5/8" 3 blades / 2 5/8" 3 blades / 2 5/8" 3 blades / 2 5/8" position hitch adjustment makes it easy to move, regardless of the hitch height of the Blade tip speed 15,485 ft/min 15,829 ft/min 18,737 ft/min 18,552 ft/min tow vehicle. The decks are lifted into positi

Nine blades generate a powerful vacuum for a crisp, clean cut. Recommended horsepower 35 40 45 50 Each deck floats independently over rolling terrain for a uniform, manicured trim. There Parking jack Standard Standard Standard Standard is a 1 ." blade overlap on the YT450, while all the other models have a 2 ." blade over- Wing frame 2" x 3" x ." wall tube 2" x 3" x ." wall tube 2" x 3" x ." wall tube 2" x 3" x ." wall tube lap. This overlap helps to prevent stripping, especially when turning. T