Оценок - 5, средний балл: 4.4
(
)
)
|
Фрагмент инструкции
Systems Checks In addition to performing individual component service, components affected by related parts changes should also receive attention at the time service is performed. Examples of this include part replacements that are part of a safety device, electrical components, transmission components, and pulleys that are part of the same power delivery system. Giving attention to related parts will help ensure that the parts most likely to be affected by the wear of similar or nearby parts, or parts subjected to the same amount of stress or wear, are given appropriate attention before a failure can occur. 1-4 Safety Rules General Information NOTES 1-5 2-1 Power Steering Conversion Kit Installation Instructions Power Steering Conversion Components Figure 1. Contents 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 24 25 26 25 26 27 28 29 32 31 30 33 12 34 12 35 36 37 38 39 41 40 Installation Instructions Power Steering Conversion Kit Ref Part No. Qty. Description 1733139A 1 TOWER, Steering 1733044A 1 PLATE, Support 1924856 4 SCREW,Taptite 5/16-18 x 1/2 1960655 2 CARRIAGE BOLT, 5/16-18 x 1-1/4 1960636 2 NUT, KEPS, 5/16-18 1933988 2 NUT, Push, 5/16 1733363 1 STEERING WHEEL 1725024 1 CAP, Steering Wheel 1733790 1 TILT STEERING UNIT 1725294 1 ADAPTER, Titt 1724685A 1 PLATE, Mounting 1924366 3 WASHER, 5/8 1960576 1 NUT, HEX, 5/8-18 1733506 1 POWER STEERING Assembly, 5-Port 1733727 1 TUBE, Hydraulic 1733211 1 TEE FITTING 1733230 2 FITTING, Perma-Push 2860444 4 SCREW, HEX, M6 x 16mm 1916964 4 WASHER, LOCK, 1/4 1701011 3 TIE, Self Locking 1935225 2 NUT, SPEED, 5/16-18 1960368 6 NUT, SPEED, 1/4-20 1732759A 1 TIE ROD 1931350 2 BOLT, 3/8-16 x 1 1611705 2 SPACER 1930645 2 NUT, Flange, Lock 3/8-16 1732937A 1 FRONT AXLE Assembly 1732439 1 STEERING CYLINDER 1702779 1 BALL JOINT 1960355 1 NUT, Hex, Lock ESNA, 1/2-13 1719725 1 SPACER 1919262 1 NUT, Hex, Jam, 1/2-20 1960713 1 SCREW, Hex, M16-110mm 1733912A 1 SPACER 1960714 1 NUT, Lock, 1/2-20 1734011 1 PIN, HitchH 1709189 1 PIN, Klik 1713578 1 ROD, 1/2 x 7-5/8 1960519 1 NUT, PUSH, 1/2 1733229A 1 HITCH, 54 Inch Mower 1733717A 1 HITCH, 44/50 Inch Mower 2-2 2-3 Power Steering Conversion Kit Installation Instructions NOTE: Read through these instructions, the SERVICE MANUAL, and OPERATOR’S MANUAL before beginning installation. INITIAL ASSEMBLY Hitch Replacement 1. Remove mower deck. See OPERATOR’S MANUAL. 2. Remove hitch (A, Figure 1) from mower deck. Note: Hardware used to attach leveling rod to hitch must be saved and re-used during reassembly. 3. Remove spring (D, Figure 1) and lever (C) from original hitch (A). 4. Discard original hitch and mounting hardware used to attach hitch to mower deck. 5. Install spring (D) and lever (C) to new hitch (B) removed in step 3. WARNING Before beginning any service work turn off the PTO, set the parking brake, turn off the ignition, and disconnect the spark plug wire(s). Front Axle Replacement 1. Remove hood assembly, dash assembly, seat and seat deck. See SERVICE MANUAL, Section 15 - Hood & Dashboard Service, and Section 16 - Seat Deck & Fuel Tank Service. NOTE: Clean and remove all debris from work area. 2. Disconnect and remove the battery. 3. Block both rear tires to prevent rolling; elevate and support the front end to allow adequate access for removal of the front axle. A B C D Figure 2 Hitch Replacement A. Original Hitch B. New Hitch C. Lever D. Spring E. Rod F. Push Nut G. Hitch Pin H. Klik Pin E F G H B 6. Install new rod (E, Figure 2) to new hitch (B), and secure in place with push nut (F). 7. Install new hitch (B) to mower deck using new hitch pin (G) and secure with klik pin (H). SEE OPERATOR’S MANUAL. DANGER PREVENT SERIOUS INJURY OR DEATH FROM FALLING UNIT Always use a properly working lifting device with a capacity suitable for the weight of the unit being serviced. Always use a jack stand to support the unit while performing service and chock remaining wheels to prevent the unit from rolling off the supports. Never work under or around an elevated unit that is not properly supported and secured in position with wheel chocks. WARNING Be careful when handling the battery. Avoid spilling electrolyte. Keep flames and sparks away from the battery. When removing or installing battery cables, disconnect the negative cable FIRST and reconnect it LAST. If not done in this order, the positive terminal can be shorted to the frame by a tool. 2-4 Installation Instructions Power Steering Conversion Kit A 7. Remove front axle and steering linkage. See SERVICE MANUAL, SECTION 8 - Steering & Front Wheel Repair. 8. Remove J-hook (A, Figure 4) from original axle (B). Save J-hook (A), 7/16-14 x 2 capscrews (C), and 7/16-14 lock nuts (D) for installation on new axle. Figure 5 Spacer Removal A. Spacer B. Original Axle B Figure 4 J-Hook Removal A. J-Hook B. Original Axle C. Capscrews, 7/16-14 x 2 D. Lock Nuts, 7/16-14 10. Thread 1/2-20 jam nut (D, Figure 6) onto steering cylinder (B). Then attach ball joint (C) to steering cylinde...
Эта инструкция также подходит к моделям:Газонокосилки - 1687286 (1.85 mb)