Войти:
Оценок - 1, средний балл: 5 ( )

Инструкция по эксплуатации Ferris Industries, модель Lawn Mower

Производитель: Ferris Industries
Размер: 2.97 mb
Название файла: edf88f06-0c9b-4f47-99cf-9a197bc21d55.pdf
Язык инструкции:itenes
Перейти к скачиванию



Фрагмент инструкции


Electrical safety Check the power cord regularly for damage and signs of wear and tear. Do not use your Turbotrimmer if the power cord is damaged. v If the mains cord or extension cable is damaged while you are working, unplug the mains plug immediately. Do not touch the cable until the mains plug is switched off. The socket of the extension cable you are using must be waterproof. v Only use permitted extension cables. v Ask your electrician. For all portable units that are operated outdoors we recommend using a fault circuit breaker. In Switzerland the use of a residual-current device is obligatory. Starting your Turbotrimmer: Trimming along lawn edges and in awkward places: 6 8 3 3 C Cutting position Park position D D 3. Operation Risk of injury if the Turbotrimmer does not switch off when you release the start button. V Never bypass the safety devices (by binding the start button to the handle, for example). I E K M N J J L Replacing the filament cassette: 13 GB 12 GB Risk of injury! Pulling the filament out of the filament cassette: L K E 5. Trouble-Shooting Risk of injury from the cutting filament! V Always unplug the mains plug of the Turbotrimmer before troubleshooting. If a filament is drawn into the filament cassette you can pull it out again as described below. 1. Unplug the mains plug. 2. Remove the filament cassette as described under 4. Maintenance “Replacing the filament cassette” . 3. Press together the plastic ring L on the filament cassette E between your thumb and forefinger. 4. Draw the plastic ring L with the thumb of the other hand over the side part of the filament cassette E (use a screwdriver if necessary). You can now access the filament that was drawn into the filament cassette. 5. Unwind the filament K approximately 10 cm and thread it through the eye of the plastic ring L. If necessary, loosen the filament beforehand using a screwdriver. The filament K may stand out max. 2 cm over the knife F. 6. Pull the plastic ring L back over the filament cassette E. 7. Reinstall the filament cassette as described under 4. Mainte-nance “Replacing the filament cassette”. Only GARDENA Service Centres and authorised specialist GARDENA dealers may carry out repairs. Fault Possible cause Remedy The Turbotrimmer Filament worn or too short. v Lengthen the filament – no longer cuts. see 3. Operation “Filament feed (Tip mechanism for automatic filament feed )”. Filament cassette empty. v Replace the filament cassette – see 4. Maintenance “Replacing the filament cassette” ). Filament drawn into the v Pull the filament out of the cassette or stuck together. filament cassette (see above). If you have any other problems please contact the GARDENA Customer Service. 6. Storage The Turbotrimmer must be stored out of the reach of children. v Store your Turbotrimmer in a dry place where it is protected from frost. Risk of injury! Risk of injury! Cleaning the cover and ventilation slots: 1. Leave the motor running. E F 2. Hold the cutting head 7 para...

Эта инструкция также подходит к моделям:
Газонокосилки - Lawn Mower (2.97 mb)
Газонокосилки - Lawn Mower (2.97 mb)
Газонокосилки - Lawn Mower (2.97 mb)
Газонокосилки - Lawn Mower (2.97 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории