Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
The use of other than factory supplied replacement parts wfll void the warranty. MODELS SEL AND SEM COVER VENT CAP AND DEFLECTOR Item No. Part No. Description Qty. 1 SK00105 Screw, Vi-20 x%* 1 2 SK50179 Washer 1 3-6 SK00054 Vent Cap Assy. 1 3 SK51032 Support Arm 1 4 SK50218 Knob 1 5 SK50131 Spacer 1 6 SK00059 Cover 1 7 SK50133 Spacer 1 8 SK50444 Knob *3,4 9 SK00175 Deflector Assy. (30 GaL) 1 SK00176 Deflector Assy. (40 GaL) 1 ♦The first figure represents the 30 gallon mode! and the second figure represents the 40 gallon model Use only replacement parts which are factory supplied as to preserve the certification of Underwriters Laboratories. American Gas Association, Canadian Standards Association or Canadian Gas Association (as applicable). The use of other than factory supplied replacement parts will void the warranty. SKILLET HINGE ASSEMBLY Item No. 1-9 1 2 3 4 5 6 7 8 9 10 11 Part No. KE00598 SK00168 KE51218 KE50823 KE50820 KE50819 FA11507 FA11284 KE50122 KE50121 KB1217 KE50824 SK50209 SK00101 Description Hinge Assy. (30 GaL) Hinge Assy. (40 GaL) Body, Hinge Pin, Hinge Insert, Hinge End Piece, Hinge Screw, Tension Adjust, 10-24 x Screw, End Piece, %-20 x Spring, Hinge (30 GaL) Spring, Hinge (40 GaL) Cytindet; Hinge Bearing, Hinge Washer Bo#,%-16x1* Qtjt 2 2 1 1 1 1 2 2 1 1 1 1 1 1 Use only replacement parts which are factory supplied as to preserve the certification of Underwriters Laboratories, American Gas Association, Canadian Standards Association or Canadian Gas Association (as appficabie). The use of other than factory supplied replacement parts will void the warranty. FLOOR MODEL ELECTRIC SKILLET SERVICING GUIDE This section contains servicing information intended for use by Authorized Service Personnel. hf 1. 2. В/ 1. 2. С/ 1. PROBLEM: Skillet fails to heat with both pilot lights on. Probable Cause Test and Remedy Faulty contactor/s Faulty wiring Check coils and contacts of contactors. Replace if necessary. Check wiring to contactors. Repair if necessary. PROBLEM: Skillet fails to heat with both pilot lights off. (ppwer switch must be on and thermostat set). Probable Cause Main power to skillet is off Defective power switch Test and Remedy Check incoming power at terminal block. With power source off, remove wiring from switch and test for continuity. Or with wiring connected and unit on, check for voltage across terminals of switch. Voltage indicates an open circuit Replace switch if necessary. PROBLEM: Skillet fails to heat with power “ON” pilot illuminated and temperature pilot off. (thermostat must be set). Probable Cause Defective thermostat Defective high limit thermostat Test and Remedy Shut the unit off and disconnect wiring from thermostat Check for continuity of thermostat An open circuit, while in the “ON” portion, indicates a faulty thermostat Or with thermostat connected and unit on, check for voltage across thermostat Voltage indicates an open circuit indicating a faulty thermostat Repeat above procedure used for defective thermostat D/ PROBLEM: Skillet fails to reach ma...
Эта инструкция также подходит к моделям:Фритюрницы - SKI-03 (827.51 kb)
Фритюрницы - SKI-03 (827.51 kb)
Фритюрницы - SKI-03 (827.51 kb)