Войти:
Оценок - 2, средний балл: 3 ( )

Инструкция по эксплуатации Cleveland Range, модель SKI-03

Производитель: Cleveland Range
Размер: 827.51 kb
Название файла: 40da1e8a-556e-4f97-aa2d-a927900a73d1.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


dwg.). HEATING ELEMENT REMOVAL 1. Tilt the skillet fully forward to access bottom cover plate. 2. Make sure power switch and external circuit breaker (at fuse box or breaker panel) are off. 3. Remove screws from bottom cover plate. Remove plate. 4. Remove four (4) 7/16 inch nuts and washers from stainless retaining plate located at rear of skillet pan. 5. Remove screws and tooth lock washer from retaining bars and slide thru open end where retaining plate was previously removed. NOTE: To remove aluminum blocks situated below Power Jack brace assembly, remove screws and lock- washers from retaining bars, but push back and then lift out at opposite end of retaining plate. The retaining bars wittrthe Power Jack brace'assemfcrty will come out as one piece. Remove the thermostat bulb (Bracket) and or safety thermostat as required. 6. Disconnect electrical lead wires from elements. 7. Remove % inch nuts and spherical washers from heating element blocks. Care should be taken when removing nuts and washers to prevent breaking the studs. 8. Remove heating element blocks. Replace as needed. NOTE: With new element block in place re-tighten nuts on washers with a torque wrench to 11 ft.-lbs. torque. 9. Replace retaining bars, retaining back plate and bottom cover. 10. Switch external power back on and return skillet to operating position. WARNING: Heating element blocks are very heavy. Use care when handling. HEATING ELEMENT BLOCK TORQUING Uneven torquing of heating element block retaining plate nuts may cause uneven heating of the cooking surface. To retorque, proceed as follows: 1. Tilt the skillet forward. 2. Ensure that the power switch and the external circuit breaker (at fuse box or breaker panel) are off. 3. Remove the bottom cover plate. 4. Loosen the % inch nuts on the spherical washers. 5. Using a torque wrench, retighten the nuts to 11 fl-lbs. torque. 6. Replace the bottom cover plate. HINGE ADJUSTMENT INSTRUCTIONS 1. Insert %' Allen wrench. 2. Turn clockwise to relieve tension on spring. 3. While tension is released remove one of the two slotted screws. 4. To prevent AUen wrench from springing back abruptly while the second slotted screw is removed, insert a pin (approximately Ve') in the hole where the first slotted screw was removed from. 5. Remove second slotted screw. 6. While holding Alien wrench remove pin. 7. Turn Alien wrench clockwise to tighten or counter-clockwise to loosen tension to produce desired effect. 8. Re-insert pin in one of the two holes. 9. Tighten one slotted screw in the other hole (it may be necessary to turn Allen wrench slightly toalign-holes.) 10. Remove pin and repeat step number 9 for other slotted screw. BUCK RED YEllOt WIRING DIAGRAM-FREE STANDING ELECTRIC, 208-240V SKILLETS 6 or .8 ELEMENTS 2400W.230 Vea, wh^ WIRING DIAGRAM-FREE STANDING ELECTRIC, 480V SKILLETS 6 or 8 ELEMENTS 2400W.230 Vea. WHTTE...

Эта инструкция также подходит к моделям:
Фритюрницы - SKI-03 (827.51 kb)
Фритюрницы - SKI-03 (827.51 kb)
Фритюрницы - SKI-03 (827.51 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории