Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
6 RESET button 7 Holding clip Adjust the holding clip to the desired angle and clip to your bag. 8 Contact point Charging the unit The unit contains a rechargeable Lithium-Ion battery, which should be charged before using for the first time. 1 Connect the supplied AC power adaptor with the battery charging stand. Battery charging stand (supplied) (Rear) AC power adaptor (supplied) 2 Connect the supplied AC power adaptor to an AC outlet. To an AC outlet Battery charging stand (supplied) 3 Put the unit on the battery charging stand. Portable Stereo Transmitter Contact pin Note If the holding clip is turned, the unit cannot be set on the battery charging stand and charging does not start. Turn the holding clip back to the original position before charging. Rest the unit on the battery charging stand so that the unit’s contact point meets the contact pin on the battery charging stand, and make sure that the indicator (red) lights up. Charging is completed in about 3 hours* and the indicator (red) goes off automatically. * Time required for empty battery to recharge. Tip When charging the battery, the unit is turned off automatically. Continued Caution If this unit detects a problem while charging, the indicator (red) may turn off, although charging is not complete. Check for the following causes: – Ambient temperature exceeds the range of 0 °C – 40 °C (32 °F – 104 °F). – There is a problem with the battery. In this case, charge again within the above-mentioned temperature range. If the problem persists, consult your nearest Sony dealer. Notes • If the battery is not used for a long time, battery may be quickly depleted, however, after a few recharges, battery life will improve. • If the life of the built-in rechargeable battery drops to half the normal length, the battery should be replaced. Consult your nearest Sony dealer for replacement of the rechargeable battery. • Avoid exposure to temperature extremes, direct sunlight, moisture, sand, dust or mechanical shock. Never leave in a car parked in the sun. • Use only the supplied AC power adaptor. Do not use any other AC power adaptor. Usage hours* Status Approx. usage hours Music playback 11 hours time (up to) * Time stated above may vary, depending on ambient temperature or conditions of use. Checking the remaining battery When pressing the POWER button while the unit is turned on, the indicator (red) flashes. You can check the remaining battery by the number of times the indicator (red) flashes. Indicator (red) Status 3 times Full 2 times Mid 1 time Low (needs to charge) Note You cannot check the remaining battery immediately after the unit is turned on, or while pairing. When the battery is almost empty The indicator (red) flashes slowly automatically. When the battery becomes empty, the unit will turn off automatically. Pairing What is pairing? BLUETOOTH devices need to be “paired” with each other beforehand. Once BLUETOOTH devices are paired, there is no need for pairing again, except in the following cases: • When pairing information is deleted after repair, etc. • When this unit is paired with 9 or more devices. This unit can be paired with 8 BLUETOOTH devices; if a new device is paired after 8 devices have been paired, the device whose latest connection time is the oldest among the 8 paired devices is replaced by the new one. • When recognition of the unit by the device to be connected is deleted. • When this unit is initialized. All pairing information is deleted. Note Passcode* of this unit is fixed at “0000.” This unit cannot be paired with a BLUETOOTH receiving device whose Passcode is not “0000.” * Passcode may be called “Passkey,” “PIN code,” “PIN number,” or “Password.” Procedures of pairing 1 Place a BLUETOOTH receiving device within 1 m (3 ft) of this unit. 2 Press and hold the POWER button for 7 seconds or more to standby for pairing while the unit is turned off. The indicator (blue) and the indicator (red) start flashing together and this unit starts searching the BLUETOOTH receiving device. Notes • After about 3 seconds, power is turned on and the indicator (blue) and indicator (red) flash together twice. Keep the button pressed without releasing until both indicators start flashing together, then release the button. This unit enters into pairing mode. • If pairing is not established within about 5 minutes, pairing mode will be cancelled and this unit will turn off. In this case, start over from step 1. Continued 3 Set the BLUETOOTH receiving device to pairing mode. This unit searches the BLUETOOTH receiving device automatically, and pairs the device. The unit tries to connect the BLUETOOTH receiving device soon after detecting it. When the BLUETOOTH connection is made properly, the indicator (red) goes off and the indicator (blue) starts flashing more slowly, indicating pairing is complete and pairing information is memorized on this unit. Notes • If Passcode input is required on the BLUETOOTH receiving device, input “0000.” • The message ...