How To Install The Batteries 1. On the bottom of the portable chime you will find a round battery release tab. Push the tab inward and slide the cover in the direction of the arrow. The battery cover will slide off. Battery Release Tab 2. Install 4 C-cell batteries (we recommend Alkaline Batteries) 3. Remove back of wireless push button and install the 12-volt battery (included) as shown below. Chime Tune Setting All wireless chimes may have more than one push button. The chime tune for each pus

1 SAF. 2 RTN KM K GREEN WHITE RED YELLOW WHITE STANLEY "L" ORANGE YELLOW RED BLUE YELLOW STANLEY M/P 2 1, В 7 7 1, В STANLEY 521 TB4-5 TB4-4 TB4^ TB4-10 TB4-9 TORMAXTDA 2 1,3, б, В В & 9 7 1, 3, б, В LO-LINX 24 VAC MTR STALL SENSORS AUX 0 STALL 1 О 0 STALL 2 0 0 EAGLE 1 0 EAGLE 2 Odoor mtd 0 SENSOR 1 Odoor mtd 0 SENSOR 2 О BODY-0 GUARD О 5 2 8 О © Ж1 lli] HI HR 24 V TRANSFORMER i S DC MOTOR SEE NOTE #1 Pre-wired switch assembly AUTO RED GREEN WHITE BLACK a Ш cr GREEN WHI

Remove the battery cover on the chime. 2. Remove the white Styrofoam block 3. Unplug the red and black wires inside the battery compartment. 4. Remove the battery pack and discard appropriately. StyrofoamBlock House Code Door Try-Me Wires Chime components Required Tools: Small flat blade screwdriver, drill, 1/16” and 5/32” drill bits, and phillips screwdriver. Included Hardware: (2) Plastic screw anchors (2) 4x20mm screws (2) 3x20mm screws (2) Double sided adhesive pads The wireless door chime K

Remove the screw and take off the door. 4. Locate the chime and pushbutton jumpers shown below. Push Button Jumpers Chime Jumpers 5. Jumpers 1-6 are used to select 1 of 64 possible home security codes. 6. To change the house code, add or remove jumpers as needed. It is recommended to change only one jumper at a time and then test the system for proper operation. Positions 1-6 on the chime and pushbutton must match exactly. Push Button Mounting Instructions Note: Avoid mounting the push button on

Included Hardware: (2) Plastic screw anchors (2) 4x20mm screws (for anchors) (2) 3x20mm screws (2) Double sided adhesive pads The wireless door chime Kit has two components: Chime (receiver) Push-Button (Transmitter). Chime Tune Setting All wireless chimes may have more than one push button. The chime tune for each push button is set with jumpers 7-9. Single Push Button Kit: If you purchased a kit with a single push button, the chime tune will be set to Ding Dong from the factory. Dual Push Butt

In addition, the push plate housing can be directly installed to any flat surface such as a wall or push plate mounting post using standard screws. Powerful Design The sleek, NEMA-4 unit is tamper-resistant with a recessed front plate and beveled edges. Aesthetically pleasing with a slim line 1.5 in. depth and no visible mounting holes on the front page. BEA-Quality Plate All active plate made of durable stainless steel. Lifetime warranty on face plate. WWW.BEASENSORS.COM HALMA CROUP COMP

FOR FURTHER ASSISTANCE DURING EASTERN STANDARD TIME AT 1-800-523-2462 FROM 8AM - 5PM. FOR AFTER-HOURS, CALL EAST COAST: 1-866-836-1863 OR 1-800-407-4545 / MID-WEST: 1-888-308-8843 / WEST COAST: 1-888-419-2564. DO NOT LEAVE ANY PROBLEM UNRESOLVED. IF YOU MUST WAIT FOR THE FOLLOWING WORKDAY TO CALL B.E.A., LEAVE THE DOOR INOPERABLE UNTIL SATISFACTORY REPAIRS CAN BE MADE. NEVER SACRIFICE THE SAFE OPERATION OF THE AUTOMATIC DOOR OR GATE FOR AN INCOMPLETE SOLUTION.WEB: WWW.BEASENSORS.COM 100 ENTERPR