In typical use, alkaline batteries will last up to 2 1/2 years. WARNING: To prevent possible SERIOUS INJURY or DEATH: • NEVER allow small children near batteries. • If battery is swallowed, immediately notify doctor. Figure 1 1. Install alkaline type A23 12 volt push button battery (included). Remove back of case by pushing in tab on bottom with a small screwdriver. See diagram inside push button for correct battery orientation. Note: If batteries are preinstalled, remove orange battery tab. 2.

Snap front of push button on. When attaching push button using double sided tape, make sure the surface of the door jamb or wall is clean. 6. Mount chime. There are three different ways to mount the chime depending upon the model of chime purchased. Determine which model you purchased Figure 4 below. Mount the chime according to the instructions for your chime. 1 2 3 4 5 6 7 ON Basic Chime with Separate Chime with Attached Chime Decorative Cover Decorative Cover Style of push button and chime ma

The chime cover style will determine orientation. 7. A cover pin is installed on two sides of the chime base. After determining correct orientation, remove, turn over, and reinstall the cover pin located on top of chime base (see Figure 1). Illustrations may vary from actual chime unit. Figure 1 - Electronic Chime Identification (2300 Base Shown) Cover Pin Volume Control Base Orientation Marking Wire Entrance Hole Front Door Tune Selection Switch (3 Selections or 10 Selections – Depending on Mod

It is recommended to only change one jumper at a time and then check to see if system is functioning properly. Note: Jumpers in positions 1 through 7 must be exactly the same for both the transmitter and chime for this system to function. -4-595-5345-06 Tune Settings Your Heath®/Zenith wireless chime has different selectable tunes: Ding (one note), Ding-Dong (two note), or Westminster (eight note) (Available on selected Heath®/Zenith chimes). The factory setting is for the Ding-Dong tune (or Wes

Manual Storage Slot: A convenient slot in the base has been provided to insert the manual for future reference. Volume Control: Turn the volume control clockwise to increase the volume or counterclockwise to decrease the volume. Reset Button: This button has a dual purpose. 1) To return to the first tune in a Group when using the Tune Selection Button to cycle through the tune selections. 2) To reset the chime in case of power failure or surge. Cover Pin: A notched cover pin is located on two si

IMPORTANT: The chime will operate with a front door connection only. The chime will not operate properly with just a rear door pushbutton installed. © 2003 DESA Specialty Products™ 598-1142-01 RESET SCROLL TUNESELECTION REARTUNE 12 12 3 4 5 6 7 8 9 OFF GROUP SELECTION 74 BASE Screw/Tornillo/Vis Wire Entrance Hole/Orificio de entrada del cable/Orifice d’entree des fils Manual Holder/ Portamanual/ Porte-guide Cover Pins/Sujetadores de la tapa/Agrafes de couvercle Mounting Hole/ Orificio de montaje

9. Twist together the wires labeled “C” and secure them with a UL approved wire nut. 10.Place chime cover securely over base (see Figure 5). 11. Restore power. Press push button(s) to test chime. 4 598-1142-01 REPLACEMENT INSTALLATION WIRING For replacing an existing transformer, see instructions supplied with transformer. WARNING: Turn power off at fuse or circuit breaker before installing transformer. 1. Verify existing chime/bell system works correctly. If no sound is heard, see Troubleshoot

Snap the front of the button back on. When attaching the doorbell button using the double sided tape, make sure the surface of the door jamb or wall is clean. © 2003 DESA Specialty Products™ 595-5707-04 The chime can be mounted by using the 3 holes in the back of the case, or by using 2 screws with the keyholes. Chime Back Case Keyhole Mounting Chime Back Case Mounting Close Chime Case From Bottom Snap the front of the chime case back on. Start with the bottom edge of the case aligned wi

You may also have other rights which vary from state to state or province to province. For a specified period depending upon model (see chart below) from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge to you. Batteries are not covered. To obtain a refund or a replacement, return the product to the place of purchase. Not Covered -Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs and oth