Operation 1) Hammer drilling operation When drilling in concrete, granite, tile, etc., press the button on the c mark side fully. Be sure to use a tungsten-carbide tipped bit. Do not apply more pressure when the hole becomes clogged with chips or particles. Instead, run the tool at an idle, then remove the bit partially from the hole. By repeating this several times, the hole will be cleaned out. 2) Drilling operation When drilling in wood, metal or plastic materials, press the button on the mar

Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 2. Do not disassemble battery cartridge. 3. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. 4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight. 5. A

3. Charge the battery cartridge with room temperature at 10°C-40°C(50°F-104°F). Let a hot battery cartridge cool down before charging it. 4. Charge the Nickel Metal Hydride battery cartridge when you donot useitfor more than sixmonths. 11 1.Switchtrigger 001894 Switch action CAUTION: •Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. To start the tool, simply pull the switch trigger

Always position the GFCI as close as possible to the power source. page 5 TOOL ASSEMBLY WARNING! To reduce the risk of injury, always unplug tool before attaching or removing accessories or making adjustments. Use only specifically recommended accessories. Others may be hazardous. Assembling Dymorigs & Vac-U-Rig® Stands For Cat. No. 4125 & 4130 only (Fig. 1). Fig. 1 Handle spoke Cradle assembly Column Base Leveling screws (4) Column bolts Socket set screws (2) Hex bolt 1. Set the base on the gro

1. Enlevez le joint caoutchoute de la base 2. Mettez le chassis au niveau avec les quatre (4) boulons de nivellement. 3. Selon les instructions du fabricant, installez une cheville d’ancrage a expansion dans la surface. Alignez la fente de la base du chassis Dymorig sur la cheville d’ancrage, puis inserez une tige ou un boulon filete au travers de la base dans l’embout filete de la cheville d’ancrage. Serrez fermement le boulon ou l’ecrou et la rondelle dans la cheville d’ancrage, selon le cas.

3. Level the rig with the four (4) leveling screws using the bubble level (4125 & 4130 only) as a guide. When the rig is level, tighten the four (4) nuts (4125 & 4130 only) on the leveling screws. 4. Connect one end of the supplied vacuum hose to the vacuum line coupler on the vacuum pad. To do this, pull back the collar on the hose and push the end of the hose onto the coupler until in snaps into place. Then, connect the other end of the vacuum hose to the coupler on the vacuum pump following t

Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. 11. Avoid accidental starting. Ensure the switch is in the off- position before plugging in. Carrying tools with your finger on the switch or plugging in power tools that have the switch on invites accidents. 12. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a

Fig. 4 Socket screw Ammeter gauge Meter box Socket screw and washer Cradle 6. Attach meter box to opposite side (see "Mounting the Meter Box"). For Cat. Nos. 4115 & 4120 only (Fig. 4). 1. Loosen the cradle lock. 2. Raise the cradle to the maximum height. 3. Lift the cradle an additional 1/2" by hand. 4. Tighten the cradle lock. 5. Loosen the socket head screw and remove the meter box. 6. Remove the meter box stud from the cradle. 7. Remove the screw and washer from the end of the pinion shaft. 8

If the plug will not fi t the outlet, have a proper outlet installed by aqualifi ed electrician. WARNING Grounded Tools: Tools with Three Prong Plugs Tools marked “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet (See Figure A). If the tool should electrically malfunction or break FUNCTIONAL DESCRIPTION 2 3 4 1 6 7 8 5 10 11 12 9 13 14 15 16 1. Rack 2. Slide 3. Slide locking wing screw 4. Drill motor 5. Grease fit