Don’t expose to rain. Keep work area well lighted. Do not use electrically powered tools in the presence of flammable gases or liquids. Keep children away3. . Children must never be allowed in the work area. Do not let them handle machines, tools, or extension cords. Store idle equipment4. . When not in use, tools must be stored in a dry location to inhibit rust. Always lock up tools and keep out of reach of children. Use the right tool for the job5. . Do not attempt to force a small tool or att

See Figure C below. Charger AdapterFigure CCordless ScrewdriverScrewdriverBitsIf any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Battery Precautions To avoid accidents, never use a different charger adapter with this tool.1. Do not expose this product to rain or wet conditions.2. To avoid damage of cable and plug, never pull the cable to disconnect the Charger 3. Adapter. Do not charge the Screwdriver if either the

To use the screwdriver function, in5. sert the Bit Adapter into the Chuck as detailed in Step 1. Insert the required screwdriver bit into the Bit Adapter. Set the drilling torque by turning the 6. Torque Control (6) so that it lines up with the Arrow on the center top of the Cordless Drill/Driver. When driving screws, start with a 7. lower torque setting. When drilling in light gauge metal or 8. wood, use a wooden block to back up the material and prevent damage to the workpiece. Mark the center

When tool performance begins to diminish, stop the tool, recharge the battery, and use a fully charged battery for optimal performance. When the Battery Pack-after initial charge-requires recharging, it must charge for 2. five to seven hours in order to operate at full power. Charging room temperature: 50° F. – 104° F.3. Depress both buttons at the rear of the Battery Pack and slide the unit down to 4. detach from the Drill/Driver. 5. The Battery Pack can only fit into the Charger (20) in one po

While holding the tool in your hand, for a clockwise rotation, move the Lever to the right. For a counterclockwiserotation, move the Lever to the left. (See Figure A.) TO CHARGE THE IMPACT DRIVER 1. NOTE: The Battery (40) requires charging. (See Figure A.) 2. When the Battery (40) requires recharging, a 1- 1-1/2 hour charge allows the tool to SKU 92472 For technical questions, please call 1-800-444-3353 PAGE 7 operate at full power. operate at full power. . (See Figure A.) 3. Make sure the Trigg

Wear restrictive hair covering to contain long hair. 7. Use eye and ear protection. Always wear ANSI approved impact safety goggles. 8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines. 9. Maintain tools with care. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and, if damaged, have them repaired by an authorized technician. The h

Save thiS manual. Copyright© 2010 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included. When unpacking, make sure that the pr

Indicates a hazardous situation which, if not avoided, will result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Addresses practices not related to personal injury. impORtant SaFEtY inFORmatiOn General power tool Safety Warnings Read all safety warnings and instructions. Failure to follow the warnings and instructions may r

Lubricate the Drill Bit with cutting oil when drilling iron or steel. Use a coolant when drilling nonferrous metals such as copper, brass, or aluminum. When the hole is drilled, remove the 8. drill bit from the hole while the Drill is still running. This prevents the Drill Bit from getting caught in the hole and causing damage. Please Note: 9. The Drill/Driver has an LED light that shines on contact area. Lightly tapping on the Trigger will activate the LED light. To prevent accidents, turn off

Do not leave the Charger unattended while charging. Charge the Battery on a inflammable surface. Move the Forward/Reverse Switch of 2. the Drill to its center, locked position. Push the Battery Release Button on 3. top of the Battery down, and slide the Battery off the handle of the Drill. Chuck (4) Torque SelectorLevel (18) Battery Release Button Slide the Battery onto the Charger. 4. Plug the Charger into a grounded120 volt electrical outlet. Verify that the charging indicator light 5. comes o