When the Battery Pack requires recharging, a 3. 3-5 hour charge allows the tool to operate at full power. Charging room temperature: 50° F. – 104° F.4. Depress both buttons at the rear of each side of the Battery Pack and slide unit back 5. to detach from the Drill. Plug Battery Pack into Adapter (30) the same way it plugs into the Cordless Drill, then slide Adapter onto Charger (29), and plug the Charger into the nearest 120 volt, grounded, electrical outlet. While charging, the Battery Pack, C

Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI-approved dust mask or respirator when working around metal, wood, and chemical dusts and mists. Always wear ear protection. Ear protection is required for any other persons in the work area. WARNING: Be aware of flying concrete chips. Keep all spectators clear of the work area. WARNING: Do not operate this tool if you have back, neck, wrist, or other conditions or injuries that will be aggravated by the severe

1. Place socket with the matching drive onto Anvil. Work piece and Work area Set up 1. Designate a work area that is clean and well-lit. 3. Secure loose workpieces using a vise or clamps The work area must not allow access by children (not included) to prevent movement while working. or pets to prevent distraction and injury. 4. There must not be hazardous objects 2. Route the air hose along a safe route to reach (such as utility lines or foreign objects) nearby the work area without creating a

It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. 2. Wear ANSI-approved safety goggles and heavy-duty work gloves during use. 3. Use only within rated torque range. Do not use for loosening. 4. Use as intended only. Do not use as hammer or pry bar. Do not use handle extension to increase force. Do not drop. 5. Inspect before every use; do not use if damaged or if parts are loose. 6. Keep

OF TORQl Motor Provides 2,300 RPM and 3, Convenient One-Touch Chuck for 50% More Compact Design: 5-3/4 Built-In L.E.D. Light Illuminates t r Added Muscle for Tough Jobs : Installation I Weighs Only 3.4 lbs. Makita built 4-pole motor delivers 1,330 in.lbs. of max torque; (0-2,300 RPM and 0-3,200 IPM) Best Fit Ergonoi Grip Shape <= Only 3.4 Ibs.with ergonomic grip Built-in L.E.D. light and one-touch chuck for simple bit insertion PERFORMANCE Models BTD141 BTD141Z LXT Li-Ion batteries

14.4V CORDLESS IMPACT DRIVER MORE POWER Model BTD130FW /mrnmm LXT battery and optimum charging system produces 280% more work with 2x more cycles makitatools.com Model BTD130FW FEATURES & BENEFITS ■ LXT Lithium-ion battery produces 280% total lifetime work with 40% longer run time and 2x more cycles ■ 4-pole motor with dual steel ball bearings produces 1,240 in.lbs. of maximum torque with 3,200 IPM and 2,400 RPM ■ 3x more power, 1,000 RPM faster & 50% more compact (5-3/4") ■ Built-i

NOTE 3: Some of the trim mounting spring clips may need to be removed to allow screens to meet the window frame easily. PLASTIC WINDOW TRIM INSTALLATION: 1. Plastic Trim Spacing: • Plastic trim must be spaced out .” to accommodate window guard. • Remove the top screws from the lower trim panels. (These panels should still be in the van). • Pull out the lower panel just enough to insert the .” nylon Spacers provided with the kit. • Screw the top of the lower trim panels back on with #10 x 1 .” sh

Remove seats and seat belts for better access to the windows. 2. Remove plastic trim surrounding the fixed body windows. Save the plastic trim for reinstallation. 3. Determine which guard goes to each window. NOTE: The perforated diamond shaped holes has one side that is smoother than the other. The smoother side goes towards the inside, facing the passenger. DOOR WINDOW GUARDS: 1. In order for guard to fit properly on frame, you must permanently remove the upper plastic trim on doors. The top o

• The window guard can now be installed as stated in section #4. See section 8 – door window guard does not have cutouts for window latches (making them inoperable). FIXED BODY WINDOW GUARD: 1. While holding the cage in place, drill 1/8” pilot holes for mounting screws. 2. Install using #10 x .” sheet metal screws provided. NOTE 1: Be careful not to drill into glass. (Use drill stop) NOTE 2: To avoid stripping of holes, do not over tighten. NOTE 3: Some of the trim mounting spring clips may need

Save the plastic trim for reinstallation. 3. Determine which guard goes to each window. NOTE: The perforated diamond shaped holes has one side that is smoother than the other. The smoother side goes towards the inside, facing the passenger. DOOR WINDOW GUARDS: 1. In order for guard to fit properly on frame, you must permanently remove the upper plastic trim on doors. The top of the lower door panel may have to be trimmed approximately .” to .”. (Note: Place guard on window frame to determine pos