Оценок - 5, средний балл: 4.2
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Example: If the TV connected to HDMI can only support up to 576p(480p), the HDMI and Component outputs are all converted to 576p(480p), even if you select the resolution switch to 1080i. • Since this product has an embedded Video Upscaler function with Faroudja DCDi technology, it can enhance a 576i(480i) DVD resolution output to 576p(480p)/720p/1080i. • You do not have to make separate adjustments, since the Home Theater and TV will be automatically adjust themselves to the optimal resolution and aspect ratio if connected to HDMI. (If the TV is an HDTV and has an HDMI Input jack, output is automatically converted to the resolution of 1080i.) • Audio will not be output if decoder is not embedded in TV during 5.1 channel disk playback. • Component output will give video in ‘576p(480p)’ mode only during DVD disc playback applied with Macrovision. • Macrovision processes scramble on analog output to prevent illegal recording. Accordingly, if you are using HDMI only, it can output 576p(480p)/720P/1080i, but is limited to 576p(480p) only if you are using component. • When both HDMI connector and COMPONENT connector are connected, COMPONENT video is not displayed. • See your TV owner's manual for more information on how to select the TV's Video Input source. CONNECTIONS Connecting the Video Out to TV You can adjust the resolution switch to set the HDMI and component (PR, PB, Y) output resolution to 576p(480p)/720p/1080i. Example: If the TV supports resolution up to 576p(480p) • If you connect the HDMI and Component outputs (PR, PB, Y) at the same time, Component output resolution changes automatically to the designated HDMI resolution. Caution Selecting Resolution Set the resolution switch to 576p(480p). • A 576p(480p) video signal is output through the HDMI and component outputs (PR, PB, Y). 1 • If copy protection is in place, output resolution is automatically converted to 576p(480p) when you play the DVD, even if you set the resolution to 720p or 1080i. Note 19 DCDi (Directional Correlational Deinterlacing) Function Converts the interlace signal to progressive to prevent flickering and to remove distortion or noise on the edge of screen. Press and hold DCDi button on the remote control for over 3 seconds. • Each time the button is pressed, the selection alternates between DCDi ON and DCDi OFF. CONNECTIONS Connecting External Components 21 Example: Digital signal components such as a Settop Box or CD Recorder. Connecting an External Digital Component Optical Cable (not supplied) Press AUX on the remote control to select ‘D.IN 1 or D.IN 2’. • Each time the button is pressed, the selection changes as follows: D.IN 1 .D.IN 2 .AUX. • You can also use the FUNCTION button on the main unit. The mode switches as follows: DVD/CD . D.IN 1 .D.IN 2 . AUX . FM. Connect the Digital In 1 or 2 (OPTICAL) on the main unit to the Digital Output on the external digital component. 1 2 Please observe the following cautions for your safety. • Make sure the unit is well-ventilated. If the unit has poor ventilation, the temperature inside the unit could rise and may damage it. • Do not obstruct the cooling fan or ventilation holes. (If the cooling fan or ventilation holes are covered with a newspaper or cloth, heat may build up inside the unit and fire may result.) The cooling fan dissipates the heat generated inside the unit so that the unit can be operated normally. The cooling fan is activated automatically to supply cool air to the unit. Cooling Fan Connecting an External Analog Component Example: Analog signal components such as a VCR or TV. Audio Cable (not supplied) If the external analog component has only one Audio Out, connect either left or right. CONNECTIONS Press AUX on the remote control to select AUX. Connect Audio In on the main unit to Audio Out on the external analog component. • Be sure to match connector colors. 1 2 • Each time the button is pressed, the selection changes as follows: D.IN 1 .D.IN 2 .AUX. • You can also use the FUNCTION button on the main unit. The mode switches as follows: DVD/CD . D.IN 1 .D.IN 2 . AUX . FM. • To listen TV sound in 5.1 channel sound through the main unit, connect the Audio In on the main unit to the Audio Output on the TV. • You can connect Video Output jack on the VCR to the TV, and connect Audio Output jack on the VCR to this product. Connecting the FM Antenna FM antenna connection 1 Connect the FM antenna supplied to the FM 75. COAXIAL terminal as a temporary measure. 2 Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a wall or other rigid surface. Selecting the Video Format Press and hold NTSC/PAL button on the remote controller for over 5 seconds while the power is turned off. •"NTSC" or "PAL" will appear in the display. At this time, press the NTSC/PAL button shortly to select between "NTSC" and "PAL". • Each country has a different video format standard. • For normal playback, the video format of the disc must be the sam...
Эта инструкция также подходит к моделям:Домашние кинотеатры - HT-DS100 (8.05 mb)
Домашние кинотеатры - HT-DS1100 (8.05 mb)