1. Open the Cabinet Door and allow the support arms to lock in place. Door must remain open during the entire cleaning procedure. 3. Twist the Whipper Chamber clockwise and pull it off the Whipper Chamber Receptacle. 4. Pull the Frother off the Motor Shaft. Notice the flat keyway on the shaft and the matching keyway inside the Frother. It is important that these two keyways are lined up when reassembling. 5. Twist Whipper Chamber Receptacle clockwise and pull it off the Motor Shaft. 9. Depress t

• Solenoid removal requires interrupting the water supply to the valve. Damage may result if solenoids are energized for more than ten minutes without a supply of water. • The use of two wrenches is recommended whenever plumbing fittings are tightened or loosened. This will help to avoid twists and kinks in the tubing. • Make certain that all plumbing connections are sealed and electrical connections tight and isolated. • Keep away from combustibles. WARNING – • Exercise extreme caution when ser

1 COMPONENT ACCESS P1561 28791.1 011500 7 SERVICE FUSE AND FUSE HOLDER FIG. 4 FUSE HOLDER 1 2 FLAFLAVORORINPUTINPUTMIXED PRMIXED PR ODUCT OUTPUT ODUCT OUTPUT 2 1 1 2 3 3 3 WATERTERINPUTINPUTREFILLREFILLMAINMAINPOPOWERWERP1561 Removal and Replacement: Fuse: 1. Remove the cap from the fuse holder. 2. Remove fuse from the fuse holder, inspect, if blown discard. 3. Install new 10 amp fuse in the fuse holder. 4. Reinstall fuse holder cap. Fuse Holder: 1. Disconnect the wires from the rear of the fuse

The mating connector must be a NEMA 5-15R. The 230 volt CE version requires 2 wire, grounded service rated 230V ac, single phase, 50 Hz. The 200 volt or 240 volt versions require 2 wire, grounded service rated 200 volts ac or 240 volts ac, single phase, 50 Hz. (Refer to the dispenser’s data plate for exact voltage requirement.) CE REQUIREMENTS • This appliance must be installed in locations where it can be overseen by trained personnel. • For proper operation, this appliance must be installed wh

12. To change mix ratio refer to MIX RATIO ADJUSTMENTS. CLEANING RECOMMENDED WEEKLY CLEANING: This should be done in conjunction with the recommended weekly cleaning of your machine. The Hoppers must be empty before starting. 1. Prepare a 1 gallon cleaning solution consisting of 1 gallon of hot water and a sanitizing cleaner which contains 3-5% chlorine based sanitizer. Mix per manufacturers instructions 2. Remove connectors from each concentrate container and place them directly into the cleani

For models installed outside the U.S.A., you must comply with the applicable Plumb- ing /Sanitation Code for your area. Artwork for P/N: 00656.0001Artwork Rev: ADrawn: REFDate: 04/22/10 00656.0001 00986.0002 00824.0002 37881.0000 ELECTRICAL REQUIREMENTS CAUTION - The dispenser must be disconnected from the power source until specified in Initial Set-Up. The 120 volt version of this dispenser has an attached cordset and requires 2-wire, grounded service rated 120 volts ac, 15 amp, single phase, 6

All notices are to be kept in good condition. Replace any unreadable or damaged labels. 41093 040408 CLEANING RECOMMENDED WEEKLY CLEANING: This should be done in conjunction with the recommended weekly cleaning of your machine. The Hoppers must be empty before starting. 1. Prepare a 1 gallon cleaning solution consisting of 1 gallon of hot water and a sanitizing cleaner which contains 3-5% chlorine based sanitizer. Mix per manufacturers instructions 2. Remove connectors from each concentrate cont

10. Place level probes in notch in rim of hoppers and install hoppers. 10. Install PAF units onto hoppers and platform. 11. Plug PAF power cord into rear of platform. 12. Plug PAF platform power cord into proper electrical outlet. 13. Attach a flexible water line to the .25” flare fitting on the back panel of the Powder Auto-Fill. NOTE: A water strainer assembly (BUNN-O-MATIC #23820.1000) should be installed in line prior to the flexible water line. NOTE - Water pipe connections and fixtures dir

: 39000.0004 Easy Clear® EQHP-10L Product No. : 39000.0001 1. Wall Mount Bracket (side) Product No. : 12542.0000 2. Wall Mount Bracket (front) Product No. : 13125.0001 3. Container Holding Shelf Product No. : 12599.0000 4. Drip Tray Product No. : 02497.0000 Patents Apply 12/06 E2 Dimensions & Specifications Model Product # Volts Amps Tank Heater Watts Total Watts Temp Settings Gal./Hr. cold water input 35*F (1-6*0) Gal./Hr. hot water input 140"F (60°C) Shipping Weight Cord Attached

: 39000.0004 Easy Clear® EQHP-10L Product No. : 39000.0001 1. Wall Mount Bracket (side) Product No. : 12542.0000 2. Wall Mount Bracket (front) Product No. : 13125.0001 3. Container Holding Shelf Product No. : 12599.0000 4. Drip Tray Product No. : 02497.0000 Patents Apply 12/06 E2 Dimensions & Specifications Model Product # Volts Amps Tank Heater Watts Total Watts Temp Settings Gal./Hr. cold water input 35*F (1-6*0) Gal./Hr. hot water input 140"F (60°C) Shipping Weight Cord Attached