Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
These items will be needed for the installation. All roller-assembly wine shelves should be removed to reduce weight and prevent them from rolling. To remove, pull the shelf out to its full extension, gently and evenly lift up on both sides of the front of the shelf and remove. Reverse the procedure to reinstall the shelf. Retract the front leveling legs to allow you to move the unit more easily during installation. You will extend the leveling legs when the unit is in its final position to reduce the possibility of the unit tipping forward. Use an appliance dolly to move the Wine Storage unit. Position the dolly at the side of the unit to prevent damage to finished surfaces. Before moving the Wine Storage unit into position, protect any finished flooring with appropriate materials. MODELS 427 | 427R Dimensions in parentheses are in millimeters unless otherwise specified. MODELS 427 AND 427R INSTALLATION MODELS 427 | 427R ANTI-TIP BRACKET INSTALLATION To prevent the unit from tipping forward and provide a stable installation, install the anti-tip bracket and extend the front leveling legs to the floor. An anti-tip bracket and hardware is provided with the Wine Storage unit. The anti-tip bracket must be installed on a solid base to prevent tipover in case several loaded wine shelves are extended at the same time. If you are installing the Model 427 or 427R in a space deeper than 24" (610), the anti-tip bracket must be installed no more than 24" (610) deep, so it engages the unit properly. It is important that this measurement be made from the front of the unit without panels, to the back of the anti-tip bracket. WOOD FLOOR APPLICATIONS Use the six #12 x 21/2" wood screws and the six 1/4" flat washers provided. Drill pilot holes 3/16" (5) diameter maximum, and be sure that the screws penetrate through the flooring material and into the wall plate a minimum of 3/4" (19). Be sure that the screws hold tight. Refer to illustration 1 below. CONCRETE FLOOR APPLICATIONS Use the two 3/8" x 33/4" concrete wedge anchors, two #12 x 21/2" wood screws and two 1/4" flat washers provided. Be sure that the anchors and screws hold tight. Refer to illustration 2 below. IMPORTANT NOTE: In some installations the subflooring or finished floor may require angling the wood screws used to fasten the anti-tip bracket to the back wall. Refer to illustrations 1 and 2 below. Make sure that there are no electrical wires in the area which the screws could penetrate. WOOD FLOOR Finished Flooring Underlayment Subflooring Wall Plate Subflooring Wall Plate CONCRETE FLOOR 11/2" min (38) Finished Flooring Underlayment SPECIFICATIONSDimension A 131/2" (343) Illus. 1 Illus. 2 MODELS 427 AND 427R INSTALLATION Installation for Concrete Wedge Anchors: 1) Drill a 3/8" (10) diameter hole any depth exceeding the minimum embedment. Clean the hole or continue drilling additional depth to accommodate drill fines. Use a carbide drill bit manufactured within ANSI B94.12-77. 2) Assemble the washer and nut flush with the end of anchor to protect threads. Drive the anchor through the material to be fastened until the washer is flush with the surface material. 3) Expand the anchor by tightening the nut 3–5 turns past hand-tight position or to 25 foot-pounds of torque. Always wear safety glasses and use other necessary protective devices or apparel when installing or working with anchors. Anchors are not recommended for use in lightweight masonry material such as block or brick, or for use in new concrete which has not had sufficient time to cure. The use of core drills is not recommended to drill holes for the anchors. POSITION THE UNIT Before moving the Wine Storage unit into position, secure the door closed. Remove the drawers of the Model 427R. IMPORTANT NOTE: For Model 427R, the top drawer has a control cable that needs to be disconnected before removing this drawer. Refer to illustration 3 below for placement and how to disconnect this fitting. For Model 427R, the drawers should be placed aside until you are ready for installation of the door and drawer panels. IMPORTANT NOTE: When two Model 427, 427R or Integrated units are installed closer than 2" (51) to one another, it is necessary to use the Sub-Zero dual installation heater kit. Contact your Sub-Zero dealer or call 800-222-7820 for the proper components and additional instructions. The heater plate from this dual installation heater kit must be attached to the left side exterior of the right hand unit before the unit is slid into position. MODELS 427 | 427R OPTIONAL COMPONENTS Optional installation components are available through your Sub-Zero dealer, or call Sub-Zero at 800-222-7820. You can also visit our website at subzero.com. Illus. 3 Dimensions in parentheses are in millimeters unless otherwise specified. MODELS 427 AND 427R INSTALLATION MODELS 427 | 427R POSITION THE UNIT IMPORTANT NOTE: If you are adding an accessory lock kit to your Model 427 or 427R, the catch should be installed at the to...
Эта инструкция также подходит к моделям:Диспенсеры - 424/O (575.93 kb)
Диспенсеры - 430/O (575.93 kb)