Be sure to remove the sticker before using the clock. • Depending on the clock model, the configuration of your clock may differ somewhat from that shown in the illustration. • This product has a sweep second hand. TO START CLOCK Insert a battery into battery compartment (©) with polarity as indicated. TO SET TIME Turn the hour/minute adjuster (@) in either direction. TO ADJUST SECONDS Remove the battery to stop the second hand at 12 o’clock position. Replace the battery at a t

Be sure to remove the sticker before using the clock. • Depending on the clock model, the configuration of your clock may differ somewhat from that shown in the illustration. • This product has a sweep second hand. TO START CLOCK Insert a battery into battery compartment (©) with polarity as indicated. TO SET TIME Turn the hour/minute adjuster (@) in either direction. TO ADJUST SECONDS Remove the battery to stop the second hand at 12 o’clock position. Replace the battery at a t

Be sure to remove the sticker before using the clock. • Depending on the clock model, the configuration of your clock may differ somewhat from that shown in the illustration. •This product has a sweep second hand. • (TQ-551) Pressing SNOOZE/LIGHT illuminates the face of the clock for about three seconds for easy reading of the time in the dark. • (TQ-551) This product has a luminous resin face that accumulates light for easier reading. • (TQ-451) This product uses luminous paint for face marking

Should either of these symptoms occur, replace the battery immediately. Do not leave a low or dead battery in the clock. To replace the battery CLOSE 1. Remove the battery cover. • Rotate the battery cover so its ▼ mark moves from CLOSE to OPEN. 2. Remove the old battery. 3. Load a new battery, making sure that its positive (+) and negative (-) ends are facing correctly. • Loading a battery incorrectly can cause it to burst and damage the clock. 4. Replace the cover. • Place the battery

•If you make a mistake, you can clear the displayed time to 00M00S by pressing the STOP/RESET button (11111). •Starting a timer operation while the start time is 00M00S causes the timer to count time upwards, like a stopwatch. 2.Start the timer. Press the START button (33333) to start timer operation. •The displayed time counts down in 1-second steps. •To pause the timer operation, press the STOP/RESET button (11111). Press the START button (33333) to restart the timer operation. •While the time

time (a+b). Press B to release. • 1st-2nd place times START SPLIT 0 a (a) STOP (b) SPLIT release STOP (t) Press A . Press B to reset. RESET (a) J (b) Press A in SPLIT mode. Press B when the first runner (a) finishes. Displays time of first runner. Press A when the second runner (b) finishes. • LAP timing (Lap timing for each segment of an event) START STOP STOP START START 0 a (a) b (b) t LAP (a) Press A in LAP mode. LAP (b) Press B to freeze LAP time (a). Press B to re

· In any mode (except when making any settings), press D to illuminate the display for just over a second. Timekeeping Mode World Time Mode Data Bank Mode Stopwatch Mode TIMEKEEPING MODE Press B. Animated display PM indicator Hour : Minutes Day of week PM indicator Hour : Minutes Seconds Month - Day · Press B to switch the display between Time/Date/Day of week and Time/Animation. · Animated figure types depend on the watch model. To make the time, date, and other settings 1. While in the Timekee

• If you do not perform any operation for a few minutes while a setting screen (with flashing digits) is on the display, the watch automatically exits the setting screen. The operational procedures for Modules 2182, 2189 and 2289 are identical. All of the illustrations in this manual show Module 2189. Timekeeping Mode Countdown Alarm Mode Day Counter Mode Alarm Mode Press B. [Module 2289] [Modules 2182, 2189] TIMEKEEPING MODE Day • When using 12-hour timekeeping, a P appears on the Minutes Secon

Press C to increase the selected number. Holding down C changes the number at high speed. • To set the starting value of the countdown time to 24 hours, set “0:00”. 4. After you set the countdown time, press A to exit the setting screen. To use the countdown timer Minutes 1. Press A while in the Countdown Alarm Mode to start Hours Minutes Seconds the countdown time. Hours • To stop a countdown operation, press A. Pressing A again resumes the countdown. • To restart the countdown, stop it and the