All rights reserved. Sealed Example High-Pass Set at 30Hz In this example, the frequency has been increased to 30 Hz Up to 6 dB of boost is capable at this frequency With +6dB of boost, the woofer has more output down to 23 Hz the overall usable output is increased Figure 8 Figura 8 Abbildung 8 Figure 9 Figura 9 Abbildung 9 AMPLIFIeR WIRInG Power Connections • Power connections accept up to 4 AWG wire • 4 AWG power and ground wire recommended for optimal performance • Connect 12V+ to the battery

AmplifierMODELXTR2502XTR5002OWNER'S MANUAL AmplifierMODELXTR2502XTR5002OWNER'S MANUAL Contents english 1 Francais 19 espanol 35 Deutsch 51 Italiano 67 Portugues 83 Introduction 2 What’s in the Box 2 Practice safe sound™ 2 end Panel Layouts 3 CeA specifications 4 specifications 5 Amplifier settings 6 signal Input and output Configurations 6 Input Gain 6 Line output Configurations 6 Internal Crossover Configurations, Flat (full range) 6 Crossover switch 6 Low-Pass Crossover 6 High-Pass Crossover 7

All rights reserved. 13 NOTE: Make sure all the equipment in the system is turned off when making or breaking connections to the input RCA’s or speaker terminals. Turn on the system and slowly turn up the volume control only after double checking all wire connections. Power for systems with a single amplifier can be supplied by most automotive electrical systems. Systems with multiple amplifiers may require a higher capacity battery, alternator or the use of a storage capacitor. We strongly reco

(70 Watts at 2.) per channel, four- channel amplifier with dual built-in high-pass and low-pass 12dB/ octave crossover and Bass Boost the XtR2504 is capable of 6, 5, 4, 3 or 2 channel operation with a maximum power capability of 250 Watts into two 4. bridged loads l XTR5004 -80 Watts at 4. (125 Watts at 2.) per channel, four- channel amplifier with dual built-in high-pass and low-pass 12dB/ octave crossover and Bass Boost the XtR5004 is capable of 6, 5, 4, 3 or 2 channel operation with a maximum

10. Due to the high-frequency MOSFET switching power supply, filtering the power cable is not generally required (remember that the amp can’t deliver full output if the power supply is restricted). Proper grounding of the signal source is mandatory for the amplifier to reach its performance peak. If the RCA inputs are not grounded adequately via the signal source, electrical noise from the vehicle may be picked up in the system. © 2002 Directed Electronics, Inc FRONT PANEL CONNECTIONS/STATUS LED

The GREEN LED will turn off and the Protection LED will light RED when the amplifier has shut itself down due to speaker short circuit, DC offset or overheating. 7. R RRe eem mmo oot tte ee S SSu uub bb L LLe eev vve eel ll C CCo oon nnt ttr rro ool ll - Controls the subwoofer amplifier gain controls from a remote location for ease of adjustment during listening. W WWa aar rrn nni iin nng gg: ::DO NOT connect a level control knob from other manufacturers to the Remote Sub Level Control of any Di

8. T TTo oop pp L LLi iig ggh hht tt O OOp ppt tti iio oon nns ss - -i. Light On W/Service Code ii. Light Off W/O Service Code iii. Light On, W/O Service Code iv. Light Off, W/Service Code Default is Light On, W/O Service Code The amplifier contains the ability to control the lights on top of the unit behind the logo badge. In addition to custom tailoring many other features, your Directed Dealer can use a Bitwriter® (V2.0 or later) to setup the top light so that it is either on or off when the

© 2005 Directed Electronics, Inc. all rights reserved PARALLEL SYNCED GAIN CONNECTIONS/SETTINGS Refer to figure 5 for wiring details. 1. I IIn nnp ppu uut tt S SSi iig ggn nna aal ll - Connect these RCA jacks as described in the Front Panel Connectionsection of this guide. 2. S SSl lla aav vve ee/ //M MMa aas sst tte eer rr S SSw wwi iit ttc cch hh • Set the slave/master switch on the master amplifier to the MASTER position. • Set the slave/master switch on the slave amplifier to the SLAVE posit

tive speakers will excite and delight the auto sound enthusiast with years of high Directed Electronics has been the quality audio reproduction. industry leader in high-quality automotive security and audio equipment since Directed SX speakers are covered by a 1990, and with the introduction of the two-year limited warranty. Be sure to SX line of high-quality loudspeakers for retain your original sales receipt, and the automobile, Directed continues to refer to the warranty section of this set n

10. Due to the high-frequency MOSFET switching power supply, filtering the power cable is not generally required (remember that the amp can’t deliver full output if the power supply is restricted). Proper grounding of the signal source is mandatory for the amplifier to reach its performance peak. If the RCA inputs are not grounded adequately via the signal source, electrical noise from the vehicle may be picked up in the system. © 2004 Directed Electronics, Inc FRONT PANEL CONNECTIONS/CONTROLS A