Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
(70 Watts at 2.) per channel, four- channel amplifier with dual built-in high-pass and low-pass 12dB/ octave crossover and Bass Boost the XtR2504 is capable of 6, 5, 4, 3 or 2 channel operation with a maximum power capability of 250 Watts into two 4. bridged loads l XTR5004 -80 Watts at 4. (125 Watts at 2.) per channel, four- channel amplifier with dual built-in high-pass and low-pass 12dB/ octave crossover and Bass Boost the XtR5004 is capable of 6, 5, 4, 3 or 2 channel operation with a maximum power capability of 500 Watts into two 4. bridged loads the installation of all orion components will determine the overall performance result Improper installation will not only limit the performance of your orion system but also potentially compromise the reliability of this amplifier to ensure proper sonic results and component reliability, please refer to your authorized orion dealer for installation assistance or advice If you decide to perform the installation yourself, be sure to read the entire manual before beginning the installation © 2008 Directed Electronics. All rights reserved. WHAt’s In tHe BoX • (1) Amplifier • (2) Allen wrenches 2mm & 3mm • (1) owner’s manual • (1) Window decal • (1) Unique individual amplifier birth certificate PRACtICe sAFe soUnD™ Continuous exposure to sound pressure levels over 100dB may cause permanent hearing loss High power automotive sound systems can generate sound pressure levels in excess of 130dB When playing your system at high levels, please use hearing protection and avoid long term exposure ReCoRD YoUR seRIAL nUMBeR AnD DAte to ensure your warranty (see back cover), please record the following information regarding your new amplifier Model: _______________________________________ serial number: _______________________________________ Date of Purchase: _______________________________________ Purchased from: _______________________________________ load conditions aren’t achieved enD PAneL LAYoUts 6 . Input Mode (Channels 1 & 2) - when the switch is out, the amplifier will accept speaker level and high output RCA connections XtR2504 and XtR5004 Figure 1 When this switch is in, it provides extra sensitivity for lower input Figura 1 voltage RCA (refer to item 4) X-Over (cross-over channels 1 & 2) -activates LPF (low pass crossover), FLAt (all pass), or HPF (high pass crossover) selection switch X-Over Frequency Control (channels 1 & 2) -FLAt (all pass) adjusts the frequency (50Hz–2000Hz) of the crossover for the HPF (High-Pass Frequency Control) and the LPF (Low-Pass Frequency Control) variable control RCA Input (Channels 3 & 4) - see item 4 definition 1234591112131014156877 8 9 Abbildung 1 1 Speakers - channels 1 and 2 2 Bass Boost -continuously adjusts from 0 to 18dB of boost centered at 45Hz 3 Gain Control (Channels 1 & 2) -continuous adjustment for full power output 4 RCA Input (Channels 1 & 2) -accepts Low Level RCA Inputs (400mV-8V) from a head unit, preamplifier, or equalizer XtR amplifiers can also accepts High Level speaker Inputs (200mV-4V) from an oeM stereo these inputs are configured by the Input Mode switch position (refer to item 6) 5 RCA Line Output - provides easy connection to additional amplifiers note that some oeM stereo headunits may sense the attached load and may turn off their speaker outputs if expected © 2008 Directed Electronics. All rights reserved. 10 . Gain Control (Channels 3 & 4) - see item 3 definition 11 . Bass Boost (Channels 3 & 4) - see item 2 definition 12 . Speakers - channels 3 and 4 13 . X-Over Frequency Control (Channels 3 & 4) -see item 8 definition 14 . X-Over (cross-over, channels 3 & 4) - see item 7 definition 15 . Input Mode (Channels 3 & 4) - see item 6 definition Figure 2, Figura 2 CeA sPeCIFICAtIons 123Abbildung 2 1 . +BAT -connect this terminal through a FUse or CIRCUIt BReAKeR to the positive terminal of the vehicle battery or the positive terminal of an isolated audio system battery WARNING: Always protect this power wire by installing a fuse or circuit breaker of the appropriate size within 12 inches of the battery terminal connection 2 . REM -this terminal turns on the amplifier when (+) 12 volt is applied Connect it to the remote turn on lead of the head unit or signal source If a (+) 12 volt remote turn lead is not available, a Remote Power Adapter (P/n #oRRPA) can be used to supply a remote turn on signal Do not connect this terminal to constant (+) 12 volt 3 . GND -power return connection Connect this terminal directly to the sheet metal chassis of the vehicle, using the shortest wire necessary to make this connection Always use wire of the same gauge or larger than the (+) 12 volt power wire the chassis connection point should be scraped free of paint and dirt Use only quality crimped and/or soldered connectors at both ends of this wire Do not connect this terminal directly to the vehicle battery ground terminal or any other factory ground points © 2008 Directed Electronics. All rights reserved. XtR2504 Power ou...
Эта инструкция также подходит к моделям:Автоусилители - XTR Amplifier XTR5004 (1.05 mb)