Green – Power applied, ON Red – Protection circuit activated, STANDBY 10 5910 XA4CH_E.p65 10 01/23/01, 12:24 PM XA4200, XA4300 ® 2CH/3CH/4CH 2 Channel The XA4200/XA4300 can be configured for three different input modes: 4 channel, 3 channel or 2 channel. 4 Channel When the input selector is set to 4 CH , the amplifier will operate as a standard 4 channel amp with all RCA inputs connected. 2CH 4CH 3CH INPUT OUTPUT REAR HI-LEVEL FRONT HI-LEVEL INPUT OUTPUT 3 Channel When the input selector is set

Proper installation is essential for optimal performance and long-term reliability. Please read through this manual first to familiarize yourself with your amplifier and its functions. Warranty Service If your Jensen amplifier should ever require service, you will need to have the original dated receipt. If you ever need to return the unit for any reason, always include the receipt with the product. Installation Assistance M – F 8:00 am to 6:00 pm EST @ 1.800.323.0221 365 / 24 / 7 @ 5910 XA4CH_E

We've tried to make the instructions in this book clear and easy to follow. For your Jensen amplifier to work right, it must be installed correctly. This manual will show you how to install your new amplifier like a pro. It's a good idea to read all of these instructions before you begin the installation. Most installations are straightforward and can be handled by a do-it-yourselfer with the right tools, patience, and the ability to follow instructions. But, do-it-yourself installation isn't fo

Do not cover the amplifier with carpets or enclose it behind interior trim panels, and do not mount the amplifier in an inverted or upside down configuration. Be sure the mounting location and the drilling of pilot holes will not damage any wires, control cables, fuel lines, fuel tanks, hydraulic lines or other vehicle systems or components. Place the amplifier in the mounting location, and mark the positions of the holes with a marker, pen or pencil. Carefully drill the mounting holes in the ma

The amplifier will remain off until it cools to a safe operating temperature. Exercise care, as the exterior of the amplifier may get uncomfortably hot to the touch before shutting down. Overload and Short Circuit Protection The amplifier will shut down if a short circuit condition exists or if electical current demands exceed safe levels. Remote Bass Control Remote bass control allows the input level to be adjusted from an alternate location. It can be mounted under-dash or in-dash. When the am

Simply plug the 6- pin modular cable into the amplifier and then into the Remote Input Level Control to activate the circuit. 50 250 500 Power Min Max 12 PowerPlus Amplifiers Troubleshooting Problem Possible Cause Corrective Action Amplifier does not turn on No power to +12V terminal Check fuse(s) No power to REM terminal Check head unit fuse(s) and wiring Blown main fuse at battery Replace fuse and identify cause of failure Blown fuse at amplifier Replace fuse and identify cause of failure Faul

Back the volume down just a bit. On the amplifier, slowly turn up the input level control (clockwise or to the right) until you just start to hear distortion, then back it down a bit. Now your radio and amplifier levels are matched. BASS EQ The Bass EQ is continuously adjustable from 0 to +12dB @ 45Hz. Adjusting the Bass Boost level allows different subwoofer/enclosure combinations to be equalized. Use this control to increase the level of low bass available from your subwoofer/ enclosure combin

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Features and Specifications . . . . . . . . . . . . . . . 3 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Speaker Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Indicators and Controls . . . . . . . . . . . . . . . . . . 11 Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Remote Input Level Contro

3 PowerPlus Amplifiers Installation Before you begin the installation of your PowerPlus series amp remember, there are two ways to do things – right and twice! Use the proper installation techniques, tools and accessories to ensure that your Jensen PowerPlus series amp will put out all the power it was designed to. If necessary, seek a professional installer to have the amplifier installed correctly. Most mobile amp installations do not have the proper gauge wire for power and ground – do not le

To ensure a good ground, scrape away any paint or undercoating to expose bare metal. Use a " ring" terminal of the proper gauge and an "outside star washer" (between the chassis and ring terminal) when making your ground connection. Although you’ve scraped away the paint to expose bare metal, the outside star washer will help to "bite into" the chassis for a tight, secure ground. Drill hole in chassis sheet metal. Replacement Fuse Requirements (FUSE) Model Quantity Amps Type 420 2 15 ATO 480 2 2