Войти:
Скачали: 30   Размер: 265 kb   Производитель: Lanzar Car Audio  
Категория: Автоусилители
@name

to the desired frequency or position. 13. Once the system is powered up, set the volume control on the head unit to about the 2 o'clock position, and then set all the amplifiers' level controls for maximum output level. 14. Further fine tuning of the various controls may be necessary to obtain the desired results. jdanzar Vibe Owner’s Manual - 5 Features and Controls VIBE700.1D / 1000.1 D / 1800D / 3100D / 4KD Level Sub Low Phase Bass sonic Pass shift Boost Cx) fx) Gc) VI 00 X) PWR PR

Скачали: 5   Размер: 265 kb   Производитель: Lanzar Car Audio  
Категория: Автоусилители
@name

Features and controls 8.9.10. System wiring 11.12. Troubleshooting X anzar Vibe Owner’s Manual - 1 Introduction Thank you for purchasing the Lanzar VIBE Class-D amplifier. Rest assured you have purchased a quality product designed and engineered to give you many years of uncompromised musical service. The VIBE Class-D amplifier has been designed using the latest in electronic technology available today This mono subwoofer amplifier is the result of advanced high speed switching technology

Скачали: 17   Размер: 265 kb   Производитель: Lanzar Car Audio  
Категория: Автоусилители
@name

Keep this ground wire less than one meter (39") in length. Use 4 gauge wire. 5. Connect the remote terminal to the remote output of the head unit using 14 gauge. 6. Connect an empty fuse holder within 300mm (12") of the battery and 4 gauge or larger highquality cable fromthis fuse tothe amplifier location. 7. Make sure there is no fuse in this fuse holder. Then make the connection to the "ВАТТ" connection on the amplifier. 8. If multiple amplifiers are being used, use cables (each with its o

Скачали: 4   Размер: 265 kb   Производитель: Lanzar Car Audio  
Категория: Автоусилители
@name

Always test the speakers and their wires first. Amplifier will not power up. Check for good ground connection. Check that remote DC terminal has at least 13.8v DC. Check that there is battery power on the + terminal. Check all fuses. Check that Protection LED is not lit. If it is lit, shut off amplifier briefly and then repower it. High hiss or engine noise (alternator whine) in speakers. Disconnect all RCA inputs to the amplifier(s)-if hiss / noise disappears, then plug in the component

Скачали: 7   Размер: 265 kb   Производитель: Lanzar Car Audio  
Категория: Автоусилители
@name

Always test the speakers and their wires first. Amplifier will not power up. Check for good ground connection. Check that remote DC terminal has at least 13.8v DC. Check that there is battery power on the + terminal. Check all fuses. Check that Protection LED is not lit. If it is lit, shut off amplifier briefly and then repower it. High hiss or engine noise (alternator whine) in speakers. Disconnect all RCA inputs to the amplifier(s)-if hiss / noise disappears, then plug in the component

Скачали: 176   Размер: 487 kb   Производитель: Lanzar Car Audio  
Категория: Автоусилители
@name

You have purchased a quality product designed and engineered to give you many years of uncompromised musical service. Heritage amplifiers are designed with the latest technology available, incorporating a DC to DC Switching Power Supply, which provides headroom for even the most demanding peaks and dynamic ranges found on modern CD's and recordings. Features • MOSFET switches maintain rated power over a wide range of battery voltages • Stiffly regulated PWM- type power supplies • 2 Ohm Stabl

Скачали: 12   Размер: 487 kb   Производитель: Lanzar Car Audio  
Категория: Автоусилители
@name

Use 8 gauge wire. 5. Connect the remote terminal to the remote output of the head unit using 14 gauge wire. 6. Connect an empty fuse holder within 300 mm (12")of the battery and run 8 gaugeor larger high quality cable from this fuse to the amplifier location. 7. Make sure there is no fuse in this fuse holder. Then make the connection to the "BATT" connection on the amplifier. 8. If multiple amplifiers are being used, use cables (each with it's own fuse at the battery) or a # O or #2 cable fr

Скачали: 9   Размер: 487 kb   Производитель: Lanzar Car Audio  
Категория: Автоусилители
@name

To the desired frequency or position. 13. Once the system is powered up, set the volume control on the head unit to about the 2 O’clock position, and then set all the amplifiers’ level controls for maximum output level. 14. Further fine tuning of the various controls may be m\necessary to obtain the desired results. Installation & Precautions Precautions 1. Before you drill or cut any holes, investigate your car's layout very carefully. Take care when you work near the gas tank, fuel line

Скачали: 8   Размер: 487 kb   Производитель: Lanzar Car Audio  
Категория: Автоусилители
@name

If it is lit, shut off amplifier briefly and then repower it. High hiss orengine noise (alternator whine) in speakers. Disconnect all RCA inputs to the amplifier(s)-if hiss/noise disappears, then plug in the component driving the amplifier and unplug it's inputs. If hiss/noise • disappears, go on until the faulty/noisy component is found. It is best to set the amplifier's input level as low as possible. The best subjective S/N ratio is obtainable this way. Try to drive as high a signal level

Скачали: 7   Размер: 487 kb   Производитель: Lanzar Car Audio  
Категория: Автоусилители
@name

Always use high quality shielded RCAcables. 3. Input Level Controls- Enables the matching of input levels to the output levels from the head unit(or other signal source). 4.High Pass Filter- When Crossover Mode Selector is in High Pass Mode, this control limits the frequencies which will be distributed to the speakers to those above the value to this is set within the range 40Hz ~ 3kHz. 5.Crossover Mode Selector- Determines the mode of built-in crossover: low pass ( permits only low frequency





Категории