Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
0.05% 0.05% 0.05% 0.05% Signal to Noise Ratio>98db >98db >98db >95db Damping Factor>175 >250 >175 >250 Separation63db 69db 60db 60db Input Sensitivity200mV-8V 200mV-8V 200mV-8V 200mV-8V 200mV-8V Input Impedance10Kohms 10Kohms 10Kohms 10K ohms 10Kohms Power Fuse 20 Amp (2)20 Amp (2)20 Amp (2)40 Amp (2)30 Amp DimensionsLength8 1/16" 11 7/8" 12 5/8" 18 15/16" 6 1/2" Height2" 2" 2" 2" 2" Width9 1/4" 9 1/4" 9 1/4" 9 1/4" 9 1/4" Crossover Selectable ON/OFF Crossover-50Hz-250Hz / 18 db/OctaveVariable Low Pass50Hz-250Hz 50Hz-250Hz 50Hz-250Hz 50Hz-250Hz 50Hz-250HzVariable High Pass 50Hz-250Hz 50Hz-250Hz 50Hz-250Hz 50Hz-250Hz N/A Variable Subsonic Filter20Hz - 60Hz 20Hz - 60Hz 20Hz - 60Hz 20Hz - 60Hz 20Hz - 60HzVariable Bass Boost at 0~+18db 0~+18db 0~+18db 0~+18db 0~+18db Before beginning the installation, consider the following: A. If you plan to expand your system by adding other components sometimes in the future, ensure that adequate is left, and cooling requirements are met. B. Are your components matched? The peak power rating of your speakers must be equal or greater than the amplifier’s. They also must be 2-8 ohms impedance (This information is normally printed on the speaker magnet). C. Consider the length of your leads which should not be too long or short when determining the mounting location. Pre-Amp input jacks require a length of high quality shielded male to male RCA patch cord. Mounting Your Amplifier The mounting position of your amplifier will have a greater affect on its ability to dissipate the heat generated during normal operation. This amplifier has ample heat sink for heat dissipation, and is designed with a thermal shutdown circuit (for heat protection). DO NOT enclose the amplifier in a small box or cover it so that air is not able to flow freely. Temperatures in car trunks have been measured as high as (155 F) in the summer time. As the thermal shut down point for the amplifier is (185 F), it is easy to see that it must be mounted in an area that provides for maximum cooling capability. To achieve maximum advantage of convection air flow in an enclosed trunk, mount the amplifier in a horizontal position. Cooling requirements are considerably relaxed when the mounting inside the passenger compartment since the driver compartment will not allow temperatures to reach a critical point. Floor mounting under the seat is usually satisfactory as long as there is at least 1 inch of clearance above the amplifier’s heat sink for ventilation. A. Select a suitable location that is convenient for mounting, is accessible for wiring, and has ample room for air circulation and cooling. B. Use the amplifier as a template to mark the mounting holes. Remove the amplifier and drill holes. Use extreme caution, inspect underneath surface before drilling! C. Secure the amplifier using the screws provided. Caution: Before connecting any wires to the amplifier, disconnect the ground lead from the battery. Leave the ground lead disconnected until you are done wiring the amplifier. PLANNING & MOUNTING YOUR SYSTEM 7C O N T R O L S & F U N C T I O N S 7C O N T R O L S & F U N C T I O N S PM3002E / PM6002E / PM1600DE 11DVMBASSREMOTE245910121314GR LR L PM3002 / PM6002E / PM1600DE 133678 DVMREMOTEPM6004EPM6004E12334567891011121314GR LR L GR LR L DVMREMOTEPM6004EPM6004E12334567891011121314GR LR L GR LR L CONTROLS & FUNCTIONS 9 DVM BASSREMOTECHANNEL3 + 4 8V 0.2 8V 0.2 8V 0.2CHANNEL1 + 2 INPUTSELECT CH1 / 5 CH1 / 4 CH1 / 2 55 CH5 PM12005EPM12005E1 2 2 3 4 5 5 678 95 1011 1213 14 15210 HI - INPUT35G 24 1 C O N T R O L S & F U N C T I O N S 9 DVM BASSREMOTECHANNEL3 + 4 8V 0.2 8V 0.2 8V 0.2CHANNEL1 + 2 INPUTSELECT CH1 / 5 CH1 / 4 CH1 / 2 55 CH5 PM12005EPM12005E1 2 2 3 4 5 5 678 95 1011 1213 14 15210 HI - INPUT35G 24 1 C O...
Эта инструкция также подходит к моделям:Автоусилители - PM12005E (1.82 mb)
Автоусилители - PM1600DE (1.82 mb)
Автоусилители - PM6002E (1.82 mb)
Автоусилители - PM6004E (1.82 mb)