Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
See Fig. 8. 2. Remove and retain secondary light and pod assembly by removing eight ( 8 ) OEM screws. See Figure 9. Figure 8 Figure 9 6 3. Attach four (4 ) pod mounting brackets (item 14 pg 2) to front and rear of bezel with four (4 ) 6-32 X 1/2" screws (item 4 pg 2) and four (4) 8-32 KEPS nuts (item 1 pg 2). See Figure 10. Figure 10 4. Install and secure O.E. bezel in overhead console (item 19 pg 2) with eight ( 8 ) # 6 X 3/8" PPH screws (item 2 pg 2) As shown. See Figure 11. Figure 11 7 5. Remove two (2) plastic tabs on secondary light and pod assembly, replace two ( 2 ) OEM screws in front assembly as shown. See Figure 12. Figure 12 6. Install and secure secondary light pod assembly in overhead console with six ( 6 ) OEM screws. See Figure13. Note: Be sure light wiring is accessible. Figure 13 8 7. Remove A/C control from rear bezel assembly. Modify A/C control by drilling three (3) 1/8" dia. holes in front mounting tabs. Position rear A/C control head in center of overhead opening. Secure with five (5) # 6 X 3/8" PPH screws (item 2 pg 2). See Figure 14. Figure 14 8. If vehicle is equipped with OEM vent switches, remove and discard blank plug in new overhead console. Retain four (4) screws. Remove and discard four ( 4 ) Figure 16 screws from OEM console. Remove and modify switch assembly by trimming four ( 4 ) tabs flush with edge. Install two ( 2 ) mounting brackets (item 15 pg 2 ) using four ( 4 ) 6-32 X 3/4" screws (item 5 pg 2 ) and four (4) keps nuts (item 1 pg 2). Install and secure OEM vent switch assembly using four ( 4 ) screws previously removed. See Figure 15. Important: Be sure vent switch assembly is centered in console openings. Manually push switch buttons to check for proper clearance and function. Figure 15 IV. INSTALLATION OF OVERHEAD CONSOLE. Caution: Do not overtighten screws. Use extra support for the console until secured to the vehicle. Failure to do so may cause damage to console or installed components. 9 1. Raise overhead console into approximate position and connect wiring to components. 2. Loosely fit console against headliner. Check that console is centered in vehicle and matches all contours of headliner. While supporting console in mounting position, loosely install using two (2) 6-32 X 3/4" screws (item 5 pg 2) through the smaller holes in bracket on console into threaded clips on mounting bracket. Inspect wiring to make sure no chaffing has occurred near the rear bracket (Item 3). 3. Secure front of console using one ( 1 ) # 8 X 1 1/2" PWH screw (item 7) in front pocket of OEM secondary pod and light assembly. See Figure 17. 4. Install one ( 1 ) # 6 x 1 1/4" PWH screw (item 6 pg 2) in dimple area at front of console through front mounting bracket. See Fig. 17. 5. Tighten 6-32 X 3/4" screws previously installed in step 2. Figure 17 Figure 19 10 6. Release video screen from locked position. Lower video screen to viewing position for access to mounting locations in top of video system housing. 7. Raise video syste...
Эта инструкция также подходит к моделям:Автомобильное видео - 1181280 (1.54 mb)
Автомобильное видео - 1181280 (1.54 mb)
Автомобильное видео - 1181281 (1.54 mb)