Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
Set assembly aside in a safe place for re-use later. 3. Remove center A/C vent in headliner using two scribe points in indicator holes on vent and twist. II. PREPARATION OF VEHICLE. 1. Place template provided (item 12 pg 2) over center A/C vent hole with arrow pointing forward. Cut and remove indicated headliner. See Figure 1. 2. Install plywood block (item 18 pg 2) provided in kit through modified louver opening and secure in place using two (2) # 8 x 9/16" PWH screws (item 3 pg2). See Figure 2 and 3. Figure 1 Figure 2 Figure 3 4 Figure 4 4. Detach wire harness from brace where A/C assembly was removed. Remove and retain two (2) OEM screws. Trim headliner to clear front flange of rear mounting bracket (item 17 pg 2) Insert rear mounting bracket tabs in existing slots on rear of OEM brace. Align holes of bracket with OEM bracket. Secure with OEM screws. See Figure 5. Route wiring toward driver’s side of bracket. Install convoluted tube (item 11 pg 2) around wire harness to prevent chaffing against bracket. Figure 6 3. Install block-off cover (item 16 pg 2) using one (1) # 8 x 1 1/4" PWH screw (item 6 pg 2). See Fig. 4. (Use caution to assure screw does not penetrate vehicle roof ). Figure 5 5. Remove and retain two (2) OEM screws located at front of OEM bracket near windshield. Mount front bracket (item 13 pg 2) using OEM holes and OEM screws. See Figure 6. 5 6. Install video system wiring into vehicle. Route video system cables from installed position in center of roof to “B”-pillar. Down “B”-pillar to floor. Route power and ground leads forward to fuse box area. Connect power wire to a fused accessory controlled power source per instructions provided in video system. Ground negative lead to chassis. Route remaining wiring (RCA plugs, Remote sensor extension, etc.) to VCP location. Connect per instructions provided with video system. If video system is to be used as a television, install an appropriate antenna per instructions included with antenna. See Figure 7. Figure 7 III. PREPARATION OF OVERHEAD CONSOLE. 1. Remove and retain OEM front control head bezel assembly by removing four ( 4 ) screws. See Fig. 8. 2. Remove and retain secondary light and pod assembly by removing eight ( 8 ) OEM screws. See Figure 9. Figure 8 Figure 9 6 3. Attach four (4 ) pod mounting brackets (item 14 pg 2) to front and rear of bezel with four (4 ) 6-32 X 1/2" screws (item 4 pg 2) and four (4) 8-32 KEPS nuts (item 1 pg 2). See Figure 10. Figure 10 4. Install and secure O.E. bezel in overhead console (item 19 pg 2) with eight ( 8 ) # 6 X 3/8" PPH screws (item 2 pg 2) As shown. See Figure 11. Figure 11 7 5. Remove two (2) plastic tabs on secondary light and pod assembly, replace two ( 2 ) OEM screws in front assembly as shown. See Figure 12. Figure 12 6. Install and secure secondary light pod assembly in overhead console with six ( 6 ) OEM screws. See Figure13. Note: Be sure light wiring is accessible. Figure 13 8 7. Remove A/C control from rear bezel assembly. Modify...
Эта инструкция также подходит к моделям:Автомобильное видео - 1181280 (1.54 mb)
Автомобильное видео - 1181281 (1.54 mb)
Автомобильное видео - 1181281 (1.54 mb)