Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
For proper functionality, the limits must be learned during the installation process. The programmed limit process uses a combination of buttons on the control board. The specific buttons used for programming depends on which side of the gates the control box is mounted on and how many operators the installation includes. Refer to pages 11-12 to determine if the gate is Left- or Right-handed and for explanation of PULL-TO-OPEN and PUSH-TO-OPEN. If a mistake is made during the programming process press the RESET button on the outside of the control box to start over. Single Arm Left-Hand Side Single Arm Right-Hand Side NOTE: The “Learn Limits” mode can be exited at any time by pressing the RESET button. The mode will time-out automatically after 60 seconds of inactivity. Z22 R91 CLOSE EDGE R94 R92 R93 L1 R1 R2 Z1 K5 K6 K2 F3 10A 32V D1O OPEN EDGE/ PHO T O OPEN PHO T O CLOSE PHO T O R227 R2O7 Z2 O R223 P1 Z9 Z8 F2 F6 D4 D2 R9 C64 JMPR1 R224 U4 CONTROL INPUTS FORCE TIMER TO CLOSE OFF MAX OPEN SINGLE BUTTON RESET STOP SHADOW INTERRUPT CHGR OVLD COM COM COM FUSE OPEN LOOP INPUTS POWER BATT 2 BATT 1 F1 20A 32V R35 D9 Z3 Z4 U3 D1 F5 C11 C13 C12 D15 R4 C2 R1O1 R1OO R9O K1 Q9 R196 Q22 D8 K3 K4 D21 D22 C4 ACCESSORY OVLD D6 JMPR2 MOV1 MOV2 DB1 U2 Z12 24 VAC/ SOLAR INPUT GATE 2 ACCESSORY POWER MAGLOCK ALARM GATE 1 C C NC NO NO GRN WHT YEL BLU RED BRN GRN WHT YEL BLU RED BRN F4 10A 32V F7 24V COM OVLD TIMER RUNNING GATE 2 SET OPEN LIMIT SET CLOSE LIMIT LEARN LIMITS DIAGNOSTIC GATE 1 J4 LEARN XMITTER MAGLOCK ON OFF L1 D4 D2 R9 C64 JMPR1 U4 FORCE R35 D9 Z3 Z4 U3 D1 D27 C11 C12 D6 JMPR2 MOV1 DB1 U2 GATE 2 SET CLOSE LIMIT LEARN LIMITS DIAGNOSTIC GATE 1 MAGLOCK ON OFF SET OPEN LIMIT LEARN LIMITS button Programming 32 Press the GATE 1 right button to move gate to the desired OPEN position. When gate is in the desired position, press the LEARN LIMITS button again. Control board will beep. OPEN EDGE/ D27 SET CLOSE DIAGNOSTIC GATE 1 Press the GATE 1 left button to move gate to the desired CLOSED position. When gate is in the desired closed position, press the LEARN LIMITS button again. OPEN EDGE/ D27 SET CLOSE DIAGNOSTIC GATE 1 OPEN EDGE/ D27 ACCESSORY OVLD Press the GATE 1 left button to move gate to the desired OPEN position. When gate is in the desired position, press the LEARN LIMITS button again. Control board will beep. OPEN EDGE/ D27 ACCESSORY OVLD SET CLOSE DIAGNOSTIC GATE 1 When the SET CLOSE LIMIT LED blinks, press the GATE 1 right button. When gate is in the desired closed position, press the LEARN LIMITS button. OPEN EDGE/ D27 ACCESSORY OVLD SET CLOSE DIAGNOSTIC GATE 1 The control board beeps and the SET OPEN LIMIT and SET CLOSE LIMIT LEDs stop blinking, programming is now complete. Z22 R91 CLOSE EDGE R94 R92 R93 L1 R1 R2 Z1 K5 K6 K2 F3 10A 32V D1O OPEN EDGE/ PHO T O OPEN PHO T O CLOSE PHO T O R227 R2O7 Z2 O R223 P1 Z9 Z8 F2 F6 D4 D2 R9 C64 JMPR1 R224 U4 CONTROL INPUTS FORCE TIMER TO CLOSE OFF MAX OPEN SINGLE BUTTON RESET STOP SHADOW INTERRUPT CHGR OVLD COM COM COM FUSE OPEN LOOP INPUTS POWER BATT 2 BATT 1 F1 20A 32V R35 D9 Z3 Z4 U3 D1 F5 C11 C13 C12 D15 R4 C2 R1O1 R1OO R9O K1 Q9 R196 Q22 D8 K3 K4 D21 D22 C4 ACCESSORY OVLD D6 JMPR2 MOV1 MOV2 DB1 U2 Z12 24 VAC/ SOLAR INPUT GATE 2 ACCESSORY POWER MAGLOCK ALARM GATE 1 C C NC NO NO GRN WHT YEL BLU RED BRN GRN WHT YEL BLU RED BRN F4 10A 32V F7 24V COM OVLD TIMER RUNNING GATE 2 SET OPEN LIMIT SET CLOSE LIMIT LEARN LIMITS DIAGNOSTIC GATE 1 J4 LEARN XMITTER MAGLOCK ON OFF L1 D4 D2 R9 C64 JMPR1 U4 FORCE R35 D9 Z3 Z4 U3 D1 D27 C11 C12 D6 JMPR2 MOV1 DB1 U2 GATE 2 SET CLOSE LIMIT LEARN LIMITS DIAGNOSTIC GATE 1 MAGLOCK ON OFF SET OPEN LIMIT With the gate in the closed position, press the LEARN LIMITS button (SET OPEN LIMIT LED will blink). Program Open Program Close LEARN LIMITS button With the gate in the closed position, press the LEARN LIMITS button (SET OPEN LIMIT LED will blink). Program Open Program Close RESET BUTTON RESET BUTTON NOTES: • If one gate is overlapping the other, the gate that is overlapping must be connected to GATE 1 so it will start moving before the other gate; gate 2 may need to be closed fi rst if there is overlap or a gate lock is being used. • The programming can be exited at any time by pressing the RESET button. Programming times-out automatically after 60 seconds of inactivity. SET CLOSE DIAGNOSTIC GATE 1 When the SET CLOSE LIMITS LED blinks, press the GATE 2 left button to close the right operator. 33 Programming Press the GATE 1 left button to open the right side operator. SET CLOSE DIAGNOSTIC GATE 1 FORCE GATE 2 SET CLOSE LIMIT LE LIMIT When the SET CLOSE LIMITS LED blinks, press the GATE 2 right button to close the left operator. FORCE GATE 2 SET CLOSE LIMIT LE LIMITS SET OPEN LIMIT N T FORCE GATE 2 SET CLOSE LIMIT LE LIMIT SET CLOSE DIAGNOSTIC GATE 1 FORCE GATE 2 SET CLOSE LIMIT LE LIMIT SET CLOSE DIAGNOSTIC GATE 1 Press the GATE 1 right button to open the left side operator. The control board beeps and the SET OPEN LIMIT and SET CLOSE LIMIT LE...
Эта инструкция также подходит к моделям:Автоматические ворота - RESIDENTIAL GATE OPERATOR GA400D (9.54 mb)