Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
For concrete and rock mounting material, allow for proper ventilation before mounting the TPS-6X-DSW. There are two Trim Ring Mount Kits. The TMK-6X-DSW is a pre-construction accessory. Pre-construction refers to framed walls prior to hanging drywall. This accessory must be used with either the Pre-Construction Mount Kit (PMK-6X-DSW) or Wall Mount Back Box (BB-6X-DSW). The WMKT-6X-DSW is a post-construction kit. Post-construction refers to framed walls with drywall hung. This accessory is designed with a mounting plate so that it can be placed anywhere on a wall without the support of a stud. The mounting plate is also ideal for installing the TPS-6X-DSW in a lectern. NOTE: Since the TPS-6X-DSW contains moving parts, mounting to a stud offers more support and is therefore highly recommended. Although Crestron offers the post-construction WMKM-6X-DSW mounting option, a mounting option that is secured to a stud, such as the BB-6X-DSW or PMK-6X-DSW is highly recommended. NOTE: If necessary, consult the latest revision of the TPS-6X-DSW Operations and Installation Guide (Doc. 6708) for a complete list of mounting options. The document is available from the Crestron website (Setup Supplied Hardware The TMK-6X-DSW consists of a metal trim ring that attaches to the BB-6X-DSW or PMK-6X-DSW. The WMKT-6X-DSW consists of the trim ring found in the TMK-6X-DSW as well as a mounting plate, cutout template and mounting screws. The mounting plate provides the necessary support for post-construction applications. An overlay cutout template (4506370) is supplied which is similar to a frame, the inner area of the frame is the shape of the required opening. Remove the center of the frame in order to use the template, refer to the illustration on page 3. Supplied Hardware for the TMK-6X-DSW and WMKT-6X-DSW DESCRIPTION PART NUMBER QUANTITY Metal, Plate, Trim Ring 2022808 1 Metal, Plate, Mounting (WMKT-6X-DSW only) 2022811 1 Screw, #06-32 x 1 1/2”, Pan, Phil (WMKT-6X-DSW only) 2007254 4 Overlay, Template, Wall Cutout (WMKT-6X-DSW Only) 4506370 1 The dimensions of the TMK-6X-DSW and WMKT-6X-DSW are shown below and on the next page. Dimensional Drawing – Trim Ring 9.28 in(23.58 cm) 6.39 in(16.23 cm) 0.52 in(1.33 cm) 1.04 in(26.27 cm) 4.00 in(10.16 cm) 2.23 in(5.66 cm) Dimensional Drawing – Mounting Plate 0.06 in(0.16 cm) 10.31 in(26.19 cm)8.00 in(20.32 cm) 8.16 in(20.73 cm) 6.35 in(16.13 cm) Drywall Cutout Template and Dimensions (supplied with WMKT-6X-DSW only 7 11/16 in(196 mm) 9 1/16 in(230 mm) 6 9/16 in(167 mm) 6 1/8 in(156 mm) Installation This section provides an installation procedure for each Trim Ring Mount Kit. The “TMK-6X-DSW Procedure” starts below and the “WMKT-6X-DSW Procedure” starts on page 6. Be sure to review each procedure before starting. TMK-6X-DSW Procedure This section provides the necessary steps for the assembly of the TMK-6X-DSW with either the BB-6X-DSW or PMK-6X-DSW. It is assumed that the BB-6X-DSW or PMK-6X-DSW has been secured to the stud according to the instructions in the latest revisions of their Installation Guides (Doc. 6728 and Doc. 6778 respectively). It is also assumed that drywall is in place and a cutout for the TPS-6X-DSW is made in the drywall. Complete the steps in the order provided. The only tool required and not supplied is a level. CAUTION: Allow an air gap of at least 12 inches (30.48 cm) in the wall cavity above and below the TPS-6X-DSW for heat dissipation. NOTE: When installing into the PMK-6X-DSW, verify that the 18 AWG bus wire securing the cables for the wall mount docking station remains attached. 1. Verify that the cutout in the drywall is as level as possible. 2. Insert the symmetrical trim ring into the opening, as shown in the illustration below. Insert Trim Ring into Opening DRYWALLTRIM RING(2022808) IMPORTANTMAKE DRYWALL CUTOUT AS LEVEL AND CLEAN AS POSSIBLE. THE TRIM RING ONLY ALLOWS MINOR ADJUSTMENTS OF THETPS-6X-DSW. NOTE: The required PMK-6X-DSW or BB-6X-DSW is not shown in the illustration above. 3. When the trim ring is in position, bend the top two flanges of the ring upward and the bottom two flanges downward. • If mounting into the PMK-6X-DSW, bend the flanges approximately 90 degrees. • If mounting into the BB-6X-DSW, bend the flanges back as far as they can go. 4. Run the necessary cables for the TPX-6X-DSW and secure them behind the drywall. 5. The wall mount docking station can be installed using the four tapped holes in the PMK-6X-DSW or BB-6X-DSW. Refer to the latest revision of the TPS-6X-DSW Operations and Installation Guide (Doc. 6708) for details. Refer also to the comprehensive illustration below. TPS-6X-DSW Mounting Using TMK-6X-DSW – Exploded View PMK-6X-DSWDRYWALLTRIM RING(2022808) TPS-6X-DSW WMKT-6X-DSW Procedure This section provides the necessary steps for the assembly and installation of the WMKT-6X-DSW into a wall. Review the procedure and complete the steps in the order provided. The only tools or materials ...
Эта инструкция также подходит к моделям:Акустика - TMK-6X-DSW (443.4 kb)