Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
The “TMK-6X-DSW Procedure” starts below and the “WMKT-6X-DSW Procedure” starts on page 6. Be sure to review each procedure before starting. TMK-6X-DSW Procedure This section provides the necessary steps for the assembly of the TMK-6X-DSW with either the BB-6X-DSW or PMK-6X-DSW. It is assumed that the BB-6X-DSW or PMK-6X-DSW has been secured to the stud according to the instructions in the latest revisions of their Installation Guides (Doc. 6728 and Doc. 6778 respectively). It is also assumed that drywall is in place and a cutout for the TPS-6X-DSW is made in the drywall. Complete the steps in the order provided. The only tool required and not supplied is a level. CAUTION: Allow an air gap of at least 12 inches (30.48 cm) in the wall cavity above and below the TPS-6X-DSW for heat dissipation. NOTE: When installing into the PMK-6X-DSW, verify that the 18 AWG bus wire securing the cables for the wall mount docking station remains attached. 1. Verify that the cutout in the drywall is as level as possible. 2. Insert the symmetrical trim ring into the opening, as shown in the illustration below. Insert Trim Ring into Opening DRYWALLTRIM RING(2022808) IMPORTANTMAKE DRYWALL CUTOUT AS LEVEL AND CLEAN AS POSSIBLE. THE TRIM RING ONLY ALLOWS MINOR ADJUSTMENTS OF THETPS-6X-DSW. NOTE: The required PMK-6X-DSW or BB-6X-DSW is not shown in the illustration above. 3. When the trim ring is in position, bend the top two flanges of the ring upward and the bottom two flanges downward. • If mounting into the PMK-6X-DSW, bend the flanges approximately 90 degrees. • If mounting into the BB-6X-DSW, bend the flanges back as far as they can go. 4. Run the necessary cables for the TPX-6X-DSW and secure them behind the drywall. 5. The wall mount docking station can be installed using the four tapped holes in the PMK-6X-DSW or BB-6X-DSW. Refer to the latest revision of the TPS-6X-DSW Operations and Installation Guide (Doc. 6708) for details. Refer also to the comprehensive illustration below. TPS-6X-DSW Mounting Using TMK-6X-DSW – Exploded View PMK-6X-DSWDRYWALLTRIM RING(2022808) TPS-6X-DSW WMKT-6X-DSW Procedure This section provides the necessary steps for the assembly and installation of the WMKT-6X-DSW into a wall. Review the procedure and complete the steps in the order provided. The only tools or materials required and not supplied are a drywall saw or equivalent and a level. CAUTION: Allow an air gap of at least 12 inches (30.48 cm) in the wall cavity above and below the TPS-6X-DSW for heat dissipation. 1. Locate an area on the wall that is free of miscellaneous wiring and studs. 2. Make a small hole near the middle of the designated site; verify that the location is suitable. NOTE: Make the cutout as level and smooth as possible. The mounting plate allows for only minor leveling adjustments. If a larger cutout is made accidentally, consider purchasing the Crestron Mud Mount Kit, MMK-6X-DSW. Together with the mounting plate supplied with the WMKT-6X-DSW, it provides a cost-effective means of correction. Essentially, the combination of these two kits makes up the Crestron Mud Mount Kit for the wall, WMKM-6X-DSW. Simply follow the “WMKM-6X-DSW Procedure” in the latest revision of the Mud Mount Kits Installation Guide (Doc. 6779). 3. Use the drywall saw or equivalent, the level and the provided cutout template to produce a level and accurate cutout in the drywall. 4. Insert the trim ring into the opening, as shown in the illustration on the following page. Insert Trim Ring into Opening DRYWALLTRIM RING(2022808) MOUNTING PLATE(2022811) IMPORTANTMAKE DRYWALL CUTOUT AS LEVEL AND CLEAN AS POSSIBLE. THE TRIM RING ONLY ALLOWS MINOR ADJUSTMENTS OF THETPS-6X-DSW. 5. Carefully pass the mounting plate through the opening and hold it against the interior surface of the drywall. 6. When the mounting plate is in position, bend the top two flanges of the trim ring upward (approximately 90 degrees) and the bottom two flanges downward (approximately 90 degrees). Refer to the illustration on the following page. NOTE: The mounting plate will have a slight play; this is normal. It allows for minor adjustments to the TPS-6X-DSW during installation. Bend Flanges – 1 of 4 Flanges Bent BACK OF DRYWALL 7. Run the necessary cables for the TPS-6X-DSW and secure them behind the drywall. 8. The wall mount docking station can be installed using the four tapped holes in the mounting plate. Refer to the latest revision of the TPS-6X-DSW Operations and Installation Guide (Doc. 6708) for details. Refer also to the comprehensive illustration on the following page. TPS-6X-DSW Mounting Using WMKT-6X-DSW – Exploded View DRYWALLTRIM RING(2022808) TPS-6X-DSWMOUNTING PLATE(2022811) SCREWS (4) #06-32 1 1/2" PAN HEAD (2007254) Resources Industry Compliance As of the date of manufacture, the TMK-6X-DSW and WMKT-6X-DSW have been tested and found to comply with specifications for CE marking. Reference Documents The latest version of all documents mentioned within the guide can b...
Эта инструкция также подходит к моделям:Акустика - WMKT-6X-DSW (443.4 kb)