Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
74 Telecaption................. .........................77, 92 Teleview..................... ...... 32, 40, 42, 78, 94 Texscan ...................... .........................18, 19 Tocom.................01, 33, 34, 42, 48, 49, 91 Toshiba...................... ...............................36 Uniden Satellite.......... ........................ 65,69 Unika.......................... ...... 01,29, 44, 88, 91 Universal................... 42, 43, 44, 52, 63, 88 Viewstar ....... 13, 20, 22, 26, 40, 58, 62, 98 Videoway.................... ...................07, 23, 50 Vid Tech..................... .............................. 64 Vidter.......................... .............................. 64 Zenith......................... ...................07, 23, 50 VCR S QSB P"0 0 О © 0 0 0 © ENTER Multi-Brand Control Setup 1 Find your TV or Cable Box or DSS Box Brand Code Number from one of the charts on this page. 2 Hold down TV or CABLE/DSS. Use the NUMBERED keys to enter your TV or Cable Box Brand code number. • For code numbers 100 or greater, first press the 100 key. Then, enter the remaining digit. E.g. for 102, press 100, then press 2. 3 To confirm that the correct code was entered, press POWER to turn your TV or Cable Box or DSS Box On/Off. Try each of the functions listed on page 33. • Due to changes in infra-red commands used by some manufacturers, more than one code may be listed for some TV or Cable Box brands. If your TV or Cable Box does not respond to the first code, please try entering the next code. Please repeat the TV/Cable Box Set Up procedure when you replace the remote’s batteries. The remote control is designed to control the brands listed. However, it will not operate all TVs, Cable Boxes or DSS Boxes made by these manufacturers. If you get no results, your particular product brand cannot be controlled by this remote control. 32 Using the Multi-Brand Control Once the remote control has been properly set up, you can select VCR, TV, or CABLE/DSS mode depending on which functions you wish to control. Press VCR or TV or CABLE/DSS on the remote control to select the desired mode. (See below for the controllable functions of each mode.) NOTE: In TV or CABLE/DSS mode, it may be necessary to press ENTER after pressing NUMBERED keys for channel selection. VCR Mode TV Mode DSSf CABLE Mode In VCR mode, the following buttons are available. VCR All function buttons. IV VOL UP/DOWN In TV mode, the following buttons are available. IV POWER, INPUT, NUMBERED keys, ENTER, CH UP/DOWN, VOL UP/DOWN VCR VCR/TV, PLAY, STOP, FF, REW, PAUSE, SLOW, REC, SPEED, COUNTER RESET, ZERO/1 MIN, SAP/Hi-Fi In DSS/CABLE mode, the following buttons are available. DSS/CABLE POWER, NUMBERED keys, ENTER, CH UP/DOWN IV VOL UP/DOWN VCR VCR/TV, PLAY, STOP, FF, REW, PAUSE, SLOW, REC, SPEED, COUNTER RESET, ZERO/1 MIN, SAP/Hi-Fi (NOTES Some TV, Cable Box and DSS Box brands require you to turn on the power manually. Not all functions listed may be controlled by this remote control. 33 More You Can Do lbril_ M lia Copying Your Tapes (Dubbing) Connections you’ll need to make. (Choose front or rear connection.) • When connecting to a normal VCR, use the L Audio In jack for proper sound reproduction. Playing (Source) VCR Recording (Editing) VCR TV for Monitoring (Audio Out (R)) 1 Insert a pre-recorded tape into the Playing (Source) VCR. Insert a blank tape with record tab into the Recording (Editing) VCR. 3 Select “LINE” Input mode on the Recording (Editing) VCR. (See “Selecting the Input Mode” at right.) 4 Press PLAY on the Playing VCR. Press PAUSE at the desired starting point. 5 Press REC on the Recording VCR, and then press PAUSE immediately thereafter. 6 Press PAUSE on both VCRs at the same time, to begin copvino. To Edit Out Unwanted Parts Press PAUSE on the recording VCR while copying is in progress. Press PAUSE again to resume copying. 7 Press STOP on both VCRs to stoo copying. To Monitor Dubbing on Your TV 1 Turn your TV on and tune to the Recording VCR channel (CH3 or CH4). 2 Set the VCR/TV Selector on the Recording VCR to “VCR.” Selecting the Input Mode Press INPUT. The display will change in the order below. Channel-► LINE1 • c Number LINE2 D or Press CH A/T. The display will change in the order below. 1 — 2 — 3' c Nl IMCO. D (CABLE) (TV) ‘LINE2<*-UNE1<*- 125 or 69 LINE1: For rear audio/video connection. LINE2: For front audio/video connection. When LINE is selected, “LI" or “L2” is displayed in the Multi Function Display for about 4 seconds. Caution: Unauthorized exchanging and/or copying of copyrighted recordings may be copyright infringement. 34 jf^\ Before Requesting Service cMn) n—--■j-"""^ Check the following points once again if you are having trouble with your VCR. Power Correction No power... • Completely insert the Power Plug into an AC outlet. • Set the POWER button to ON. Recording & Playback Correction TV program canno...