Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
3. Remove knob. 4. Hold the valve shaft with a pair of pliers and insert a thin, flat tipped screwdriver into the shaft. While viewing the burner, adjust to a minimum stable flame. 5. WARNING! Look for stability in the low flame setting. A too small burner flame may go out or be extinguished easily. Unburned gas can then escape creating a hazardous condition. NOTE: It is normal to hear a popping sound when the burners are first turned OFF. BEZEL VALVE STEM INSTALLATION OF YOUR DYNASTY GRILL (continued) installation Leak Testing Perform a leak test at least once each year whether the gas supply cylinder has been disconnected or not. In addition, anytime the gas cylinder is connected to the regulator or any part of the gas system is disconnected or replaced, conduct the leak testing. This applies to natural gas as well as propane gas. As a safety precaution, remember to always leak test your grill outdoors in a well ventilated area. Never smoke or permit sources of ignition in the area while doing a leak test. Do not use a flame, such as a lighted match, to test for leaks. Use only a leak testing solution as specified below. Leak Testing Procedure 1. Prepare a leak testing solution of sudsy water by mixing in a spray bottle half liquid soap and half water. 2. Check and make sure all the control knobs are in the OFF position. 3. Turn cylinder valve knob counter clockwise one turn to open. 4. Apply leak-testing solution by spraying on joints of the gas delivery system. 5. Blowing bubbles in the soap solution indicates that a leak is present. 6. Stop a leak by tightening the loose joint or by replacing the faulty part with a replacement part recommended by the manufacturer. Do not attempt to repair the cylinder valve if it should become damaged. The cylinder must be replaced. (continued next page) Installation 13 14 Leak Testing Procedure (continued) 7. If you are unable to stop a leak, shut off the gas supply at the cylinder valve. Remove the cylinder from the grill. Call an authorized gas appliance service technician or LP gas dealer. Do not use the appliance until the leak is corrected. 8. Push in and turn any control knob to release pressure in the hose and manifold. 9. Turn off the control knob. Installing the Heat Deflector The Heat Deflector should be fully inserted in its position, as shown, before using the grill. installation HEAT DEFLECTOR 15 Installation installation Installing Access Doors Models DADA-18, DADA-30 and DADA-42 1. Provide cut out and doorjamb with inside dimensions as follows: 19 3/8" X 16 1/4" for DADA-18, 19 3/8" X 28 1/4" for DADA-30, and 19 3/8" X 40 1/4" for DADA-42 2. Check fitting of frame against cutout. Mark location of rivet nuts. 3. Secure the steel frame with 16 screws of type #10 X 3/4 truss head phillips S/S. 4. Attach doors to frame. (See figure 2) 5. Adjust doors as follows: a) For height adjustment, loosen the two screws attached to each mounting plate. (See figure A) b) Snap off hinge and secure mounting plate with #6 X 1 flat phillips S/S. (See figure B). c) For side adjustment turn screw to increase or decrease door overlay. (See figure C) d) For depth adjustment, loosen screw, adjust door to desired position and retighten screw. (See figure D) FIG A HEIGHT ADJUSTMENT FIG B SECURE MOUNTING PLATE FIG C SIDE ADJUSTMENT FIG D DEPTH ADJUSTMENT 16 FEATURES OF YOUR GRILL Operation Feature Index See page 1 Grill Operation 18-20 Cleaning and Maintenance 32-35 2 Top Burners Operation 24-25 Flame Size 25 3 Smoke Drawer Operation 21 4 Rotisserie Operation 22-23 5 Grill Racks Cleaning 32 6 Drip Tray Cleaning 33 7 Exterior Surfaces Cleaning 33 8 Battery Igniter Maintenance 35 9 Questions? Easy Troubleshooting Guide 36-37 SPIDERS AND OTHER INSECTS WARNING… safety Spiders and other insects can nest in the burners of the grill and block the gas and airflow to the burner ports. This creates a dangerous condition that can result in a fire from behind the valve panel. It is good practice to inspect the burners for blockage and clean them regularly; in addition, such inspection and cleaning is absolutely necessary if any of the following conditions exists: a) Smell of gas in conjunction with a yellow flame. b) Grill does not heat completely. c) Grill heats unevenly. In case any of the above conditions is present, turn off the grill immediately; after allowing it to cool, inspect and clean the burners as described on pages 34-35 of this manual. BEFORE USING YOUR GRILL… Prior to turning the gas on, inspect the gas supply piping or hose. Make sure only the supplied hose and regulator are being used. If signs of abrasion, cuts wear and tear, or other damage are noticed on the hose, it must be replaced. Contact your local Dynasty dealer for replacement parts. Safety 17 18 USING YOUR GRILL Your Dynasty grill consists of a set of U-burners, a bed of ceramic briquettes and a heat retaining cooking rack. Located above the burners, the stainless steel trays supporting the ceramic briquet...
Эта инструкция также подходит к моделям:Грили - Modular System DOBB1803A (1.18 mb)
Грили - Grills DOBQ3000A (1.18 mb)
Грили - Modular System DOBB3003A (1.18 mb)
Грили - Modular System DOBB4203A (1.18 mb)