Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Visit for the newest manuals, firmware, and software Warnings: The EOS 0610i DUOII is a carefully-designed charger with many built-in safety features, such as reverse polarity protection, input voltage error warning, and cell-count mismatch warnings for lithium chemistry batteries. HOWEVER, IT IS THE RESPONSIBILITY OF THE USER TO INSURE THAT THE CHARGER IS CONFIGURED AND USED IN A SAFE MANNER IN PROPER ENVIRONMENT. • Always be sure that the charger is properly configured for the correct battery type • Be sure that your lithium battery pack balance connector matches the multi-adapter type connected to the charger. • SYNC MODE charging should start with packs at nearly equal discharge states (see more details in text) • Be sure that the batteries you charge are capable of charging at the rate you select • Never charge batteries unattended • Charge only in a fire-resistant environment, non-flammable surfaces such as on concrete or brick • Do not charge near easily flammable materials • Do not charge batteries inside a model • Charging outdoors is recommended whenever practical • Use only high-quality gold 4mm bullet connectors for charge output cable connection to the charger. See “setup” • Properly insulate and regularly inspect all connectors to eliminate the possibility of short circuit. Damage caused by output short circuit is not covered by warranty. • Never allow the charger case to contact an AC/DC power supply case while powered • Do not drop or cause other shock to the charger, nor subject it to moisture, condensation or liquids • Do not attempt to charge battery packs made from different types of cells, a mixture of old and new cells, or cells made with chemistry not supported by the EOS 0610i DUOII • NEVER attempt to charge “non-rechargeable” cells • Do not open the case of the charger under any circumstances. Doing so will void the warranty • Keep the charger away from children or pets at all times. • NEVER ATTEMPT TO CHARGE A SINGLE BATTERY ACROSS BOTH PORTS. (example: a “single unit” 10S pack) DOING SO WILL DAMAGE THE CHARGER, BATTERY, AND WILL VOID YOUR WARRANTY. DUOII is designed to charge single packs up to 6S max. For flight packs larger than 6S, DUOII supports SYNC MODE charging of two packs to make a single series-wired flight pack. (so 2x2S=4S up to 2x6S=12S series flight packs are possible) PUT SAFETY AHEAD OF ALL OTHER CONSIDERATIONS! SEEK MEDICAL ATTENTION IN EVENT OF ANY INJURY! Specifications & Features: • 180W Per Port for 360 Watts Max CHARGE Output • 0.1A to 10.0A max CHARGE Current in 0.1A steps • 50W Per Port DISCHARGE with 10A Max Current • STORE MODE allows fast and simple charge/discharge to 60% capacity for proper storage of Lithium Batteries = longer battery life. • Charges/Discharges 1 to 6 cells Lithium Polymer Batteries Per Port (3.7V/cell nominal types) • Charges/Discharges 1 to 6 cells Lithium Ion Batteries Per Port (3.6V/cell nominal types) • Charges/Discharges 1 to 6 LiFePO4 (A123) cells (LiFePO4 3.3V/cell nominal, A123 3.3v support) • Charges/Discharges/Cycles 1-16 cell NiCd/Ni-MH in three modes: Normal, Linear, and Automatic • Charges/Discharges 1~12 cell Lead Acid Batteries (Pb, 2V/cell) • Allows Lithium-Type batteries to 50,000mAh and PB (lead/acid) batteries to 100Ah capacity • Two built -in Hyperion LBA10/300 Balancers with 10A max rating and 300mA max balance rate/cell • TCS - Terminal Capacity Selection • Rich Data Displays during and after charging and balancing • PC Port for Data Logging and Firmware upgrades • Temperature Sensor Ports & Temp Stop settings* • Wide Voltage Input Range 11v~28v for higher efficiency when charging high-voltage packs, and compatibility with a wider selection of AC/DC power supplies • Power Supply Amperage Control to allow reliable charging with lower-output power supplies • Power Supply Voltage Control (PS Load Control) works in concert with Amperage control to insure the charger does not overload your power supply • Adjustable Power Sharing % between Outputs • Input Cable with 4mm Male Connectors + Clamps • Output Cable Set Included, with 4mm Connectors • Two, Integral, Thermostat-Controlled Cooling Fans • Rugged Aluminum Case with Insulating End Caps • 2-Line, 16-Character, Yellow Backlit LCD Data Display. Highly visible in all conditions • Total of 20 User-definable Memory Positions • Firmware upgradable via Win PC ** * Temp sensors available separate: #HP-EOSTMPSEN or EOS1210i-SEN ** Firmware upgrades require USB Adapter #HP-TI-PRGUSB and harness #HP-EOS06-PCCBL. Firmware upgrades will only become available if and when improvements are identified in future. HIGH RISK CHARGING ADVISORY Avoid charging batteries indoors. If you must charge indoors – or any place injury to persons or damage to property could occur in the event of fire – then be sure to: * Keep battery well away from flammables (2 meters or more) * Contain battery in a heavy fireproof container (such as a brick box) * Always monitor...