WARNING: IN ALL CASES, MAKE CERTAIN THE RECEPTACLE IN QUESTION IS PROPERLY GROUNDED. IF YOU ARE NOT SURE HAVE A QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE. GROUNDED OUTLET BOX CURRENT CARRYING PRONGS GROUNDING BLADE IS LONGEST OF THE 3 BLADES GROUNDED OUTLET BOX GROUNDING MEANS ADAPTER Fig. A Fig. B 4 EXTENSION CORDS Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which has a 3-prong grounding type plug and matching receptacle which w

All line connections should make good contact. Running on low voltage will damage the machine. Do not expose the machine to rain or operate the machine in damp locations. MOTOR SPECIFICATIONS Your machine is wired for 120 volts, 60 HZ alternating current. Before connecting the machine to the power source, make sure the switch is in the “OFF” position. GROUNDING INSTRUCTIONS This machine must be grounded while in use to protect the operator from electric shock. 5 1. All grounded, cord-connected m

NOTE: This sheet of instructions and safety information is not meant to cover allpossible conditions and situations that may occur. Read entire Operating & Maintenance Instructions for this engine AND the instructions for the equipmentthis engine powers. Failure to follow instructions and safety information couldresult in serious injury or death. The safety alert symbol () is used to identify safety HAZARD SYMBOLS AND MEANINGR information about hazards that can result in personal injury A signal

A A Fig. 3 Fig.4 6 MOUNTING THE AIR CLEANER TO THE CEILING OR OVERHEAD SUPPORT This unit weighs approximately 60 pounds. When mounting overhead, be certain that the unit issecurely fastened and supported. 1. Locate the four 1" eye bolts and the four 1/4-20 flange nuts supplied with the unit. 2. Use a flat blade screwdriver (not supplied) to remove the four screws (C) Fig. 5 from the top of air cleaner (D). 3. Thread one flange nut on each bolt approximately 3/4". 4. Thread the eye-bolts (F) Fig.

Included in Engine Gasket Set.Ref. No.358. . Included in Valve Gasket Set.Ref. No 1095. . Included in Carburetor Overhaul Kit.Ref. No. 121. Illustrations cover a range of engines. Parts shown without corresponding text may not be used on your specific engine. 3533.9 Assemblies include all parts shown in frames. 04/10/2007 9 44Q700 REF. NO. PART NO. DESCRIPTION REF. PART NO. NO. DESCRIPTION REF. PART NO. NO. DESCRIPTION 192 209 211 212 213 216 219 220 222 690083 793340 691019 695238 691021 691022

0025, 0027, 0113, 0115, 0116, 0117, 0119, 0120. Screw (Casing Clamp) Used on Type No(s). 0016, 0026, 0100, 0110, 0111, 0112, 0412, 0884. Washer.Sealing Washer (Governor Control Lever) Bracket.Rod Screw (Dipstick Tube) Muffler 304 792301 Housing.Blower 305 691005 Screw (Blower Housing) 305B 790690 Screw (Blower Housing to Intake Elbow) 309 499521 Motor.Starter 310 691263 Screw (Starter Motor) 311 497608 Brush Set 332 691059 Nut (Flywheel) 333 691060 Armature.Magneto 334 691061 Screw (Magneto Arma

Used on Type No(s). 0110. ...... Note ...... 793340 Spring.Governor (Orange) (Used After Code Date 06081400). Used on Type No(s). 0113. 698071 Spring.Governor (White) (Used Before Code Date 06081500). Used on Type No(s). 0110, 0113. 793343 Spring.Governor (Purple) Used on Type No(s). 0115, 0118, 0119, 0121. . Included in Engine Gasket Set.Ref. No.358. . Included in Valve Gasket Set.Ref. No 1095. . Included in Carburetor Overhaul Kit.Ref. No. 121. Illustrations cover a range of engines. Parts sho

[2] Disconnect spark plug wires and keep away from spark plugs. Dis- connect battery (if equip- ped with electric starter) at negative terminal. [3] With engine OFF but still warm remove oil drain plug and drain oil into appropriate receptacle. [4] Reinstall drain plug. Remove dipstick. [5] Fill to FULL mark on dipstick with new oil. Do not overfill. Note: Engine without oil filter holds approximately 1-7/8 quarts (60 ounces; 1.8 liters). Engine equipped with filter holds approximately 2 quarts

0110, 0113, 1113. Gear- -- Timing Retainer- -- E Ring Screw (Oil Pump Cover) Screw (Oil Pump Cover) Used on Type No(s). 0127, 0128, 1113, 1188, 1198, 1199, 1201, 1262, 1274. Gear- -- Pinion 788 691039 788A 793145 789A 790544 789B 698330 789C 696576 797 693167 798 697890 801 691283 802 691286 842 691031 847 499602 851 493880s 865 691012 865A 793205 865B 691015 868 690968 877A 393537 877B 399916 877C 393456 Bracket- -- Fuel Pump (Used Before Code Date 06072800). Bracket- -- Fuel Pump (Used After C