Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
• Use pipe joint compound or Teflon tape on out6, Repeat procedure on side pipe threads. outlet side. 1. Solder pipe to threaded connector, Allowto cool. Place o-ring seal on • When all piping fits together... threaded adaptor. Put ...solder all sweat fittings. adaptor into bypass ...prime and cement all PVC joints. valve port and install clip. 2. Put threaded ...tighten all threaded joints. •_ adaptor into bypass valve port. [] CAUTIONS: • Never solder fittings while connected to nonmetallic parts. Wait until soldered pipe has cooled before connection (see fig. 11). • Be careful when putting pipe fittings together. Do not cross thread, and do not overtighten. 3-4 Deluxe Valve [i!i! ::i:i ! ::i:i ! ::i SECTION 3 STEP BY STEP GUIDES TO INSTALL D. CONNECT VALVE AND SALT TANK DRAINS _1_ CONNECT THE VALVE DRAIN HOSE • Keep the hose lower than the drain fitting. (In Take a length of 3 / 8" inside diameter drain tub-some homes, to get to a drain you must raise the ing and attach one end to the drain fitting (FIG. hose and run it over-head. If you need an overhead 12). Use a tube clamp to hold it in place. Put the drain, do not raise the hose more than 8' above the other end of the tubing over a floor drain, into a floor. A copper drain tube is best to use.) laundry tub, standpipe, or other suitable drain. COPPER DRAIN TUBE: The plumbing codes Check your local codes. where you live may say that you must use a copper • Leave an air gap of about 1-1/2" between the end valve drain tube. A copper tube is also best to use for of the hose and the drain. This gap is needed so you an over-head drain. Use a copper drain tube if the don't get a back-flow of sewer water into the soften- softener is installed outside, or in the sunlight. Heat er. Do not put the end of the hose into the drain or from the sun makes many kinds of rubber or plastic connect without the air gap. hose to soften, flatten and close up. • Place and support the hose so it does not kink or To adapt a copper drain tube to the softener, buy a have sharp bends. So water pressure does not cause compression fitting (1/4 in. female pipe threads x the hose to "whip", tie or wire it in place. Do not 1/2 in. O.D. tube) and tubing from your local hard- pinch the hose shut. The softener will not work if ware store. this drain hose is pinched, plugged, closed or restricted in any way. DELUXE VALVE Optional copper drain hook-up, check with local codes _/_ _/L_ 11/4NPT Threads barbs "i ! Diameter clip _ "::/ Copper Tube cut barbs # (not furnished) from drain fitting (pull clip and remove lilting from valve) .2"--... Comp Fitting, 1/4 NPT x 1/2 in. OD. Tube -... N\ (not furnished) x\ grommet tube XX \\ adaptor \\ NN " _ tube \\ X\ STANDPIPE K\ N\ l_lamp \x_... To drain point "_ other than valve drain hose floor drain. (see step 1, above) Support tubing in place as needed. r gap 1 1/_p, tie or wire air gap 1-'_/' air gap tubing in place 1 NOTE: Overflow drain tubing is available from Sears, Item No. " 27 42 -3433 (20 ft) overflow drain - tubing (see step 2, top of page 3-6) 3-5 Deluxe Valve [i!i! ::i:i ! ::i:i ! ::i SECTION 3 STEP BY STEP GUIDES TO INSTALL Ol CONNECT VALVE AND SALT TANK DRAINS _ CONNECT SALT TANK OVERFLOW TUBING e Take the rubber grommet, tube adaptor and tube clamp (FIG. 12) that are on the small parts cardboard liner. @Push the grommet into the hole in the salt tank wall so half is inside and half is outside. @Push the bigger end of the tube adaptor into the grommet. e Push one end of a length of 3 / 8" I.D. tubing onto the tube adaptor, using the tube clamp to hold it in place. Put the other end of the tubing over the floor drain. Important: • The salt tank overflow is for safety only. If the salt tank should overfill with water, the overflow tubing carries it to the drain. • Over-fill water must run downward through the tubing. Do not raise the tubing higher than the grommet and tube adaptor (FIG. 12). • Do not connect to the valve drain hose you installed in step 1. Both drains must have a separate hose or tube. 3-6 Deluxe Valve li!i! ::i:i ! ::i:i ! :i SECTION 3 STEP BY STEP GUIDES TO INSTALL E. PRESSURE TEST / CHECK FOR LEAKS [] CAUTION: HOUSE MAIN WATER SHUTOFF VALVES To avoid water or air pressure damage to soft-Shutoff _) ener inner parts, and to flush pipe chips or other residue from the water pipes, be sure to do the following steps exactly as instructed. _ _ Water Shutoff Look at the picture in FIG. 15 showing your kind of bypass valve(s). _1_ Fully open two cold, soft water faucets nearby the softener. Bypass valve(s) should always remain in soft _Jl Place bypass valve(s) a single valve, slide in the "bypass" position. On stem inward to bypass. water service position. Position if needed for softener repairs. in bypass only On a 3-valve system, close the inlet and outlet valves and open the bypass valve. SINGLE BYPASS _ Fully open the house main water pipe shutoff PULL STEM valve (closed in step 1, page 3-1). Observe OUTWARD steady water fl...
Эта инструкция также подходит к моделям:Водоочистители - 170 (1.87 mb)
Водоочистители - 180 (1.87 mb)
Водоочистители - 280 (1.87 mb)