Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
2-4 Deluxe Valve SECTION2 PLAN YOUR INSTALLATION D. TYPICAL THREADED IN AND OUT PIPES TO SOFTENER If you are planning a threaded plumbing installation, with a 3-valve bypass, use the drawing in Fig. 4 as a guide. Use union fittings, as needed, to connect the plumbing. DELUXE VALVE MODELS ucets Outside So ft ":!_':_'::" :".... M (Raw W _e ater In) FITTINGS REQUIRED NOT L DENTIFIED Union (2) 90 o Elbow (2/ Pipe (as reg,) IN _ 1" NPT ,o,e _ adaptori_c°,'o_:? _o_V_o_o,_ *NOTE: For 1 in. plumbing connection, use a 1 in, threaded straight connector. 2-5 Deluxe Valve li!i! ::i:i ! ::i:i ! ::iSECTION 3 STEP BY STEP GUIDES TO INSTALL A. ASSEMBLE INLET-OUTLET ADAPTORS, OR PLASTIC BYPASS VALVE Shutoff Close the shut-off valve on S ffi the house main water pipe, near the water meter or pressure tank, to turn off the wa C C -_"" -_ " Water Meter Pump ter. Shut off the gas or electric T supply to the water heater. Electrical Open the highest and lowest Panel water faucets in your house to let water drain from the pipes. Close faucets after water has drained. 0 Visually check and remove any foreign materi ffi If not already done, remove als from the valve inlet and outlet ports (FIG. 6). N all cardboard or plastic pack- Carefully remove the two large plastic clips (you ing pieces from inside the MJJJJJJJJJJJJJJJJ will use them). Check to be sure the turbine and softener. Set the cardboard MJJJ JJJJJJJJJJJ turbine support are firmly in place. (Fig. 6) MJ JJJJJJJJJJ liner (with parts for installing MJJJ JJJJJJJJJJ MJ_dJdJdJdJd MJ JJJJJJJJJJ _dJ dJdJdJdJd 0 fastened to it) where you can BYPASS VALVE: If not already done, put a light MJJJJJJJJJJJJJJJJ MJJJJJJJJJJJJJJJJ easily see it, and get to parts coating of silicone grease on the o-ring seals and as you need them. slide onto the bypass valve. Push the bypass valve into the softener valve as far as it will go. Remove the main Snap the two large holding clips into place, cov- Salt Hole Cover from the top down as shown. (Fig. 7) er...putl outward on 2 (M_n) tabs to release. For the UltraSoft 100 remove [] CAUTION...Be sure the clips snap firmlythe salt hole cover into place so the bypass valve will not pull out. first. For the UltraSoft (Fig. 7) 200 the salt hole cover remains attached to the main cover when GO TO PAGE 3-4. removed. So they will INLET AND OUTLET THREADED ADAP- not get scratched or 0 TORS: If not already done, put a light coating of broken, set both covers aside. silicone grease on the o-ring seals and slide onto the threaded adaptors. Push the adaptors into the valve inlet and outlet ports, or bypass valve ffi INSTALL SEARS BYPASS VALVE AND / ports, as far as they will go. Both adaptors are OR THE INLET OUTLET THREADED the same and fit either port. Snap the two large ADAPTORS (FIG. 4, 5 AND 6). All needed holding clips into place, as shown. (Fig. 7) parts are on the small parts skin-pack. Note: CAUTION...Be sure the clips snap firmly If you will not install the bypass valve because you into place so the tubes will not pull out. (Fig. 7) will have a 3-valve bypass, skip step b, but do steps a and c. GO TO PAGE 3-3. 3-1 Deluxe Valve [i!i! ::i:i ! ::i:i ! :i SECTION 3 STEP BY STEP GUIDES TO INSTALL A. ASSEMBLE INLET-OUTLET ADAPTORS, OR PLASTIC BYPASS VALVE DELUXE VALVE MODELS INSTALLING BYPASS VALVE, and / or INLET and OUTLET THREADED ADAPTORS Before installing the bypass valve, or threaded adaptor, be sure the turbine and support are firmly in place in the valve outlet port. turbine sensor support port S \ turbine included with softener Valve inlet included with softener INSTALLING HOLDING CLIPS BYPASS VALVE TURNED DOWNWARD black cross section of valve inlet or outlet bypass valve or threaded adaptor TURN BYPASS VALVE UPSIDE DOWN TO CONNECT TO FLOOR LEVEL PLUMBING clip snaps into place o-ring IN between larger diameter rings 3-2 Deluxe Valve [i!i! ::i:i ! ::i:i ! :i SECTION 3 STEP BY STEP GUIDES TO INSTALL B. INSTALL 3-VALVE BYPASS _ INSTALLING 3 VALVE BYPASS AND PIPES (FIG. 9) O Cut the house main water pipe where you will connect the softener. Loosely put together pipe, fittings, and the 3 valves. Place valve(s) within easy reach. 3 -VALVE BYPASS (threadedplumbing shown) IMPORTANT: When looking at the front of the softener, the inlet is on the right side. If water in your house main water pipe runs from left to right, be sure to use a "cross-over" as shown on page 2-3. When all pipe, fittings and valves make a good fit together, tighten all threaded joints (use pipe dope on outside threads), or solder all sweat joints. 1 to softener inlet 3-3 Deluxe Valve li!i! ::i:i ! ::i:i ! :i SECTION 3 STEP BY STEP GUIDES TO INSTALL Ci LOCATE WATER SOFTENER, AND CONNECT PIPES I! MOVE THE SOFTENER INTO PLACE MOVE SOFTENER INTO PLACE Move the softener into place, onto a level and smooth surface. If needed, put a piece of 3/4" plywood, at least 17" x 20", under the tank. Then put spacers under the plywood to level the softener. Do not put shims or spacers directly under gri...
Эта инструкция также подходит к моделям:Водоочистители - 170 (1.87 mb)
Водоочистители - 275 (1.87 mb)
Водоочистители - 280 (1.87 mb)