Оценок - 5, средний балл: 3.8 ( )

Производитель: Sears Размер: 1.17 mb Название файла: 8b5dee9d-23cf-4c45-a552-554da6d29d60.pdf Язык инструкции:

6. SLOWLY, reposition the bypass valve(s) to service... FIG. 8, page 18. Open the nearest_ water faucet until you can smell chlorine, then close. m Again, put the bypass valve(s) in bypass position. Allow the filter to stand idle for about 45 minutes, while the chlorine sanitizes. 1 After the 45 minutes, return the bypass valve(s) to service. Then, press face plate button [] to start a backwash. While the filter completes this automatic backwash and fast rinse . .. takes about 35 minutes.., turn to page 7 and make the timer settings. 1 When the backwash/fast rinse is over (water flow to drain stops), open filtered water faucets until chlorine odor is gone, then close the faucets. C) Reoommended by the Water Quality Association. On some water supplies, the water filter may need periodic disinfecting. 6 SECTION 1 WATER FILTER START-UP I 1D. PROGRAM THE TIMER I Q PRESENT TIME AND DAY ] _ BACKWASH TIME I, _ BACKWASH DAY _ SETICLEAR ON/OFF VACATION V_,_.:J _ BACKWASH NOW display buttons When the transformer is plugged into the electrical outlet, 12:00 AM, SUnday began to flash in the time display. Set the time of day, present day of week, and days/time of backwash, as follows. 1. SET TIME OF DAY a. Press the PRESENT TIME AND DAY button [] once. The hour display continues to flash. b. Press the SET/CLEAR button [] until the present hour of the day shows in the display. Be sure AM for morning hours, or PM for afternoon and evening hours shows. NOTE: Press SET/CLEAR and quickly release to move the hour display ahead 1 at a time to the correct hour. Or, hold the SET/CLEAR button to move the display ahead 2 hours each second, to the correct hour. C. Press button [] once to steady the hour display, and minutes begin to flash. Repeat step lb to set the correct minutes. d. Press button [] again to steady the minute display (day will begin flashing). Figure 2 shows the timer set at 3:30 PM. 2. SET PRESENT DAY OF WEEK a. Press the SET/CLEAR button [] to set the present day of the week in the display. NOTE: Press SET/CLEAR and quickly release to move the day display 1 at a time. Or, _ the SET/CLEAR button to move the day display ahead 2 days each second. b. Press the PRESENT TIME AND DAY button [] again to steady the entire display. Figure 2 shows the timer set at TUesday. Q PRESENT TIME AND DAY I o3:30] {_ (_ BACKWASH BACKWASH TIME DAY EXAMPLE: This drawing shows the present time of day at 3:30 PM, and the _ SETICLEAR present day on TUesday. _ ON/OFF VACATION HOLD BACKWASH NOW (continued) 7 SECTION 1 WATER FILTER START-UP 1 D. PROGRAM THE TIMER 3. SET DAYS OF BACKWASH IF YOU HAVE A WATER SOFTENER OR OTHER AUTOMATIC FILTER, .. A good water flow rate is needed for proper recharging and/or backwashing of all water conditioners. To help assure good water flow, you should offset the timers on each conditioner so recharges do not occur on the same days, or at the same time. •.. Most Sears water softeners are factory set (many are adjustable ) to recharge from 2:00 to 4:00 am. •• • Set the filter to backwash on different days, or... •• • Set the filter to backwash either before or after other equipment, or... ... Offset the timers on all equipment to J29.g_ recharges on backwashes at 12:00, 2:00 and 4:00 AM, or 1:00, 3:00 and 5:00 AM, etc. a. Read the BACKWASHING GUIDE for your type of filter. b. Press the BACKWASH DAY BUTTON [] AND SUnday begins to flash. If you want backwashes on Sunday (from guide), press the SET/CLEAR button [] to display ON. If you do not want Sunday backwashes, press button [] to display OFF. NOTE: The timer is factory programmed to backwash on Monday, Wednesday and Saturday• C. Press b...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: