Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
It heats the water as it passes through the appliance. The continuous-low heater switches on and heats the water when the warm water tap is opened. It switches off as soon as the tap is closed. The appliance may not be operated with pre-heated water, as otherwise the overtemperature protection will trip. This installation and operating instruction manual describes various appliance types: Over-sink appliances: –DE06111 and DE08111: for ixed electrical connection Undersink appliances: –DE04101 and DE10104: with plug connection – DE05101, DE06101 and DE08101: for ixed electrical connection DE 05101 DE 06101 DE 08101 DE 04101 DE 10104 DE 06111 DE 08111 185185 14088 1 2 1 1 4 5 67 3 4 5 17 enen Preparations for installation Only for DE04101 and DE10104 ¦ Shut off the water supply before connecting the appliance. The electrical connection must be disconnected from the mains supply. Unscrew the fuse or switch off the circuit breaker. For all appliances A clearance of about 60 mm on all sides of the appliance is required for installation. ¦ Observe the technical appliance data. ¦ Break out the installation bracket from the rear of the appliance (A). ¦ Break out one of the side knock-outs (B1) provided for an incoming electrical supply cable. ¦ Feed the desired length of the incoming electrical supply cable downwards through the knockout (B2). ¦ Important: Connect the unit only to a mains socket with protective contact that is installed according to regulations. Do not use an extension cord. If necessary, equip the unit with a longer cord. B2 B1 AA 18 enen Only for DE05101, DE06101, DE06111, DE08101 and DE08111 (ixed electrical connection) ¦ Press the upper and lower latches ( C1), then remove the housing cover (C2). C2 C1 C1 C2 C1 C1 19 20 en Wall mounting Undersink appliances ¦ Attach mounting template D to the wall. ¦ Mark the locations for the holes; drill the holes and insert the wall plugs. ¦ Attach the installation bracket to the wall using the screws (D1). Only for permanently installed appliances: ¦ Pass the connection cable through the cable grommet, suspend the appliance in the installation bracket and screw it onto the mounting bracket (D2). Only for appliances with mains plug: ¦ Suspend the appliance in the installation bracket and screw it onto the mounting bracket (D3). D3 D1 D D2 D1 D 50 100 en en Over-sink appliances ¦ Attach mounting template E to the wall. ¦ Mark the locations for the holes; drill the holes and insert the wall plugs. ¦ Attach the installation bracket to the wall ( E1). ¦ Pass the connection cable through the cable grommet, suspend the appliance in the installation bracket and screw it onto the mounting bracket (E2). Only for DE05101, DE06101, DE06111, DE08101 and DE08111 (ixed electrical connection) ¦ The variants for feed through of cables using lush mounting electrical connection should be observed on the mounting template. ¦ The cable grommet must completely enclose the connection cable to guarantee optimum protection against dampness. The opening must be sealed watertight if it is damaged. ¦ Use the openings provided on the rear for mounting. E2 E1 E 50 100 21 22 en Water connection ¦ The appliance is only approved for heating water with a speciic electric resistance of . 1 300 .cm at 15 °C. Your water utility company can give you information about the speciic water resistance. Installation ¦ Ensure the axial it of the connection pipes in the nozzles. ¦ Tighten the union nuts on the nozzles with an open-end wrench and counter hold with a suitable open-end wrench. ¦ The T-piece (for the pressurized connection) and lexible connection hose are available commercially. ¦ Use an unpressurized tap for the unpressurized connection, e. g. the tap available as a special accessory (Single-lever mixer tap BZ13061, Two handle ixture BZ13051). ¦ Exchange the perlator from the tap ixture with the supplied aerator to change the spray pattern of the tap. Controlling temperature The supply temperature (probably lower in winter) and pressure luctuations can inluence the temperature of the water leaving the tap. ¦ Turn the valve slowly in the closed direction for higher temperatures (F1). ¦ Add cold water for lower temperatures (F2). F2 F1 F2 F1 pressurized (closed) unpressurized (open) en en For all appliances Electrical connection ¦ Vent the continuous-low heater: Fully open DE05101, DE06101, DE06111, DE08101 the warm water tap and lush out the appliance and DE08111 (ixed electrical connection) for about 1 minute (G), until bubbles no longer emerge. ¦ Connect the appliance on the terminal strip in accordance with the connection schematic. ¦ Put on the housing cover and push it onto the rear wall of the appliance so that the upper and lower latches engage. DE04101 and DE10104 Replacing the Power Supply Cord: ¦ The power supply cord must be replaced by our customer service only in order to avoid a hazard. The mains plug must be pulled before replacing. 1 min G L N PE E2E1 F1 F2 X1 DE 05101 DE 06...
Эта инструкция также подходит к моделям:Водонагреватели - DE10104/03 (7.8 mb)