Оценок - 4, средний балл: 3.8 ( )

Производитель: Empire Comfort Systems Размер: 4.54 mb Название файла: Язык инструкции:

Refer to Figure 56. Receiver Shutdown of Burner • In the remote, auto mode the valve shuts off if it does not receive a signal within 3 hours from the transmitter • In the local mode the valve does not shut off • In the remote, manual mode the vavle shuts off if it does not receive a signal within 6 hours from the transmitter Thermopiles • The negative leads (white) must be connected to the terminals with the one white dot marked next to them • Each thermopile must provide at least 500 mV open circuit voltage • If output is erratic, check thermopile for intermittent shorts LED Troubleshooting Note: In normal operation, LED blinks once every two seconds; also, LED will be on for one second after every valid command received by the RV8310D; these are not error codes. Failure codes (see Table) can occur anytime after the pilot burner is lit. Failure code timing is 1/4 second on, 1/2 second off. Sequence is failure code followed by LED not blinking for four seconds. In the event of multiple failure codes, the next failure code follows the previous failure code by approximately three seconds. Code Service Action 8 Replace valve 7 Confirm stepper motor connection exists 4 Fuel conversion plug missing or has poor connection (RV8310E only) 3 Replace thermopile with Q313 2 Device too hot. Check application 1 None required. This is normal operation and indicates the control is powered For additional Standing Pilot Troubleshooting refer to Page 30 Page 40 17375-6-0705 RF TRANSMITTER FUNCTIONS FIRST USE OF TRANSMITTER Status Begin communication between transmitter and receiver/valve. Transmit unique code. Confirm recognition between transmitter and receiver/valve. Chose Remote or Local operation. Operation in the Remote Position AUTO Mode Action Move LOCAL/REMOTE Switch to LOCAL position for at least two seconds; then move switch to the REMOTE position. Press Fan or Flame key within 30 seconds. Observe LED turns on for one second. Move LOCAL/REMOTE switch to LOCAL or leave in REMOTE. With the control in the AUTO mode, the flame in the main burner will turn on, off, or change height based on the heat needed to maintain the set temperature. Status Set to AUTO. Change set temperature. Flame. Fan. To Set Delay Timer. Action Press MODE button until mode is AUTO. Press UP or DOWN key to change set temperature. Automatically changes. Automatically changes. Press TIME key followed by either an UP or DOWN arrow key. CAUTION Properly Damage Hazard. Excessive heat can cause property damage. In AUTO mode, the main burner will cycle indefinitely to maintain the set temperature. Keep the transmitter in a heated living space to make sure that the main burner is not on continuously. On Mode When the control is in the ON mode, the flame and fan levels and the delay timer are changed with the UP and DOWN arrow keys. Status Set to ON. Flame. Fan. Delay Time. OFF Mode The flame in the main burner will turn off and the room temperature will be displayed in the remote window. Operation in the LOCAL Mode. Action Press MODE button until mode is ON. Press FLAME button and press UP or DOWN arrow key to change flame height. Press FAN button and press UP or DOWN arrow key to change fan speed. Press DELAY TIMER button and press UP or DOWN key to change timer. Press MODE until mode is OFF. NOTE: Remote/Local switch on the receiver/valve must be in the LOCAL position. FAN Flame height and fan speed both go to the highest position. Other Functions: Change between Fahrenheit and Celsius temperature units. Fan Override during AUTO Mode. Disable thermostat function in the AUTO Mode In LOCAL mode, to turn flame on/off, rotate manual knob from ON to PILOT position. Press UP and DOWN arrow keys at the same time and hold for at least three seconds. Press FAN button, and press UP or DOWN arrow key to change the fan speed. Press the TIME, DOWN and FLAME arrow keys at the same time and hold for at least three seconds. 17375-6-0705 Page 41 RF WIRING DIAGRAM WIRING DIAGRAM WITH BLOWER Figure 56 Page 42 17375-6-0705 17375-6-0705 Page 43 STANDING PILOT LIGHTING INSTRUCTIONS RF STANDING PILOT LIGHTING INSTRUCTIONS MAINTENANCE AND SERVICE PLEASE NOTE It is normal for appliances fabricated of steel to give off some expansion and/or contraction noise during the start up or cool down cycle. Similar noises are found with your furnace heat exchanger or car engine. It is not unusual for your gas fireplace to give off some odor the first time it is burned. This is due to the curing of the paint and any undetected oil from the manufacturing process. Please ensure that your room is well ventilated -open all windows. It is recommended that you burn your fireplace for at least six (6) hours the first time you use it. If optional fan kit has been installed, place fan in the “OFF” position during this time. IMPORTANT: Turn off gas before servicing appliance. It is recommended that a qualified service person perform these checkups at the beginning of each heating season. • Clean ...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: